YSPAG-210 bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YSPAG-210 model number is decoded

YSPAG 210 is SKF's 50 mm-bore SKF ConCentra insert bearing with concentric stepped-sleeve locking and symmetrically extended inner ring in the YSP2 series — a Y-bearing with a spherically ground outside surface for static self-alignment inside a matching SKF Y-housing, boundary dimensions 50x90x46.2 mm. The ConCentra principle replaces point or eccentric clamping: a stepped sleeve between shaft and inner ring is driven axially to contract uniformly, concentric with the sphered-OD sealed ball insert. the YSP prefix names SKF ConCentra locking: a stepped (multi-diameter) sleeve between shaft and inner ring is driven axially to grip concentrically, avoiding the local shaft fretting of set screws or the imbalance of an eccentric collar. the size code 210 carries the usual bore arithmetic — 50 mm (code 10 x 5) — while the leading 2 marks the ISO 15 diameter series 2 sphered-OD envelope. AG marks the agricultural-machinery application execution, built on the sealed both-sides-extended geometry and tuned for the low-speed, shock-laden duty of harvesters, balers and spreaders — note the catalogue prints a much reduced limiting speed for this variant. Envelope 50x90x46.2 mm (1.969x3.543x1.819 in), outer ring 22 mm wide, C 35.1 kN, C0 23.2 kN, Pu 0.98 kN. The catalogue publishes a single speed ceiling, the limiting speed: 800 r/min; mass 720 g. Capacity density: 35.1 kN from 0.720 kg of bearing steel is about 48.75 kN per kilogram, and per width millimetre the 46.2 mm unit carries 0.76 kN of dynamic capacity. Rating split for the maintenance file: dynamic 35.1 kN (L10), static 23.2 kN (s0 shock check), fatigue 0.98 kN (adjusted life) — three separate uses for YSPAG 210, none interchangeable with another. Imperial procurement cross-check: 1.969 in bore, 3.543 in OD, 1.819 in overall width; the 720 g mass converts to 0.720 kg (25.4 oz) for the bill of materials. Speed ceiling of 800 r/min is the catalogue mechanical limit for THIS execution; the AG agricultural derate is deliberate, so real fan duty is planned well below it. Spherical-seat note in numbers: the 90 mm OD is ground spherical, so the self-aligning pivot happens on a circle roughly pi x 70 = 219.911 mm in mean circumference — keep that interface greased, because corrosion locking turns the pivot into a fixed misaligned mount. Sleeve geometry: the ConCentra stepped sleeve occupies the symmetric extension up to the 46.2 mm overall width while the sphered outer ring stays 22 mm wide — uniform sleeve contraction is why run-out stays low at 50 mm bore.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• ConCentra solves run-out and fretting but not gross misalignment — the housing spherical seat still carries that function; do not use the sleeve grip as an excuse to skip housing alignment.
• Inspect the shaft before sleeve mounting: a single deep keyway burr or old screw-point dimple under the 46.2 mm-wide sleeve causes a local unclamped arc that later frets.
• The SB shortened-inner-ring ConCentra unit needs its matching mounting sleeve and procedure; substituting a standard YSP sleeve or a generic drift is the usual cause of crooked drive-up on the 50 mm shaft.
• Ordering discipline for the 50 mm size: the chapter lists several executions side by side (YSP2 locking style x seal package x application variant); a bare-number substitution needs a fresh dimension, speed and rating check rather than a like-for-like assumption.