C4024-V bearing: complete specifications & equivalents
The C4024-V is a ISO 15 radial bearing sized 120 x 180 x 60 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 120 mm |
| Outer diameter D | 180 mm |
| Width B | 60 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 530 kN |
| Basic static load rating C0 | 880 kN |
| Fatigue load limit Pu | 91.5 kN |
| Limiting speed (mechanical) | 1100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 5550 g |
| Manufacturer designation | C 4024 V |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & C4000-series range
| Bore d | 4.724 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 2.362 in |
| ISO bore code | 24 |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in C4000-series | 50 mm |
| Largest outer diameter in C4000-series | 1030 mm |
| Width range across C4000-series | 30–315 mm |
| Bore position in C4000-series (smallest first) | 6 of 16 |
| Bore above smallest C4000-series size | 70 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| C4024-2CS5V-GEM9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 120×180×60 mm envelope, but catalogue C/C0 differ between the cylindrical-bore full-complement V and cylindrical-bore sealed full-complement V executions (530/880 kN vs 430/640 kN) — envelope match, not a load-rating equivalent. |
| C4024-V-VE240 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 120×180×60 mm envelope, but catalogue C/C0 differ between the cylindrical-bore full-complement V and cylindrical-bore full-complement V executions (530/880 kN vs 430/640 kN) — envelope match, not a load-rating equivalent. |
| C4024-K30V-VE240 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 120×180×60 mm envelope, but catalogue C/C0 differ between the cylindrical-bore full-complement V and 1:30 tapered-bore K30 full-complement V executions (530/880 kN vs 430/640 kN) — envelope match, not a load-rating equivalent. |
| C4024-K30V | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 120×180×60 mm ISO 15 envelope and equivalent catalogue C/C0; C 4024 K30V is the 1:30 tapered-bore K30 full-complement V execution of this size — boundary dimensions interchangeable, only mounting and cage execution differ. |
| 24024 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 120×180×60 mm envelope as the SKF spherical roller bearing SKF 24024 CC/W33, but catalogue C/C0 differ (530/880 kN vs 456/670 kN) — and the functions differ: spherical locates axially, CARB floats. Pair them; never swap one-for-one. |
| 24024-CCK30-W33 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 120×180×60 mm envelope as the SKF spherical roller bearing SKF 24024 CCK30/W33, but catalogue C/C0 differ (530/880 kN vs 456/670 kN) — and the functions differ: spherical locates axially, CARB floats. Pair them; never swap one-for-one. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the C4024-V model number is decoded
SKF lists C 4024 V in the dimension series 40 CARB toroidal roller bearings: the toroidal roller profile both follows tolerates angular misalignment and lets the inner ring slide axially inside the outer ring, giving free axial displacement at the non-locating position. Reading the code: C marks the CARB toroidal family, the first two digits (40) identify the ISO dimension series and the last two (24) encode the 120 mm bore; suffixes describe bore and execution. The cylindrical 120 mm bore mounts directly on a machined seat; the outer ring takes a loose housing fit so the bearing can float axially. The same size is listed in both bore executions, and the boundary dimensions 120×180×60 mm are identical — only the mounting method changes. Float capacity is a selection criterion: the catalogue lists the permissible axial displacement (s) for the 60 mm wide set; size the free-end housing so thermal growth stays within it, not just inside the overall width. Seat tolerances follow the ISO 15 recommendation for the normal-load position — the 180 mm outer ring typically takes a loose housing fit to preserve float, and the rings must be supported across their full faces.
Typical equipment & failure modes
Common applications
- continuous-caster guide rolls and slab-caster segments under heat growth
- vibrating screen exciters fitted with the VE240 tolerance execution
- long fan and kiln main shafts where the free end must float without thrust load
- heavy industrial gearbox layshafts used as the non-locating position
Known failure patterns
- roller-end and flange smearing after lubricant starvation at the long roller contacts
- edge loading and premature spalling when the CARB position is blocked from its designed axial float
- brass cage pocket wear under marginal lubrication in the large-bore M/MB executions
- false brinelling and rust-red witness marks on standby machines under external vibration
- grease churning and overheating when a high-speed thrust position is over-packed
Selection pitfalls — read before you substitute
- At 120 mm bore, shaft expansion is already measurable: calculate the required float inside the 60 mm wide bearing rather than assuming the free-end clearance is "enough" at operating temperature.
- Tapered-bore K executions mount on adapter sleeves (1:12) and K30 on withdrawal sleeves (1:30) — the 120 mm bore changes the sleeve family, and the drive-up procedure differs accordingly.
- Reference and limiting speeds are different limits: the catalogue lists no thermal reference speed for this full-complement/sealed execution, the limiting value is the mechanical ceiling; observe the reference under load unless the arrangement calculation says otherwise.
- The quoted 530/880 kN ratings belong to this exact execution (C 4024 V); VE240 vibrating-screen variants and sealed 2CS/2NS variants have their own figures even at the same envelope.
- Do not block the axial displacement in the drawing: housing covers, labyrinth rings and snap rings must leave the catalogue float (s) free, or the bearing silently becomes a poorly located fixed bearing.
- The 530/880 kN ratings and 5550 g mass are SKF catalogue values transcribed from ch. 10.1 of PUB BU/P1 17000 (PDF table page 862); mounting data — axial displacement (s) and seating details — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
Which dimensions does the C 4024 V have?
A C 4024 V measures 120 mm bore × 180 mm outside diameter × 60 mm width (4.724 × 7.087 × 2.362 in). From SKF catalogue PUB BU/P1 17000: dynamic C 530 kN, static C0 880 kN, fatigue limit Pu 91.5 kN, limiting speed 1,100 r/min, no reference speed listed, mass about 5550 g.
What does C 4024 V mean in SKF part numbering?
C marks CARB; 40 the dimension series; the size code gives 120 mm bore; V is the execution (cylindrical bore for direct shaft fitting, full-complement V execution (no cage)). The envelope follows ISO 15 and matches spherical roller bearing outlines, but the functions differ.
Why is C 4024 V used opposite a spherical roller bearing?
The spherical bearing locates the shaft and takes thrust; the CARB bearing at the other end self-aligns but floats, absorbing thermal expansion without inducing axial load. The pair is standard on paper machine drying cylinders and long caster rolls.
Is the C 4024 V sealed?
No, it is an open execution relying on the housing seals; the full-complement V design has no thermal reference speed in the catalogue.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings on 2026-09-27. Read our editorial & correction policy.