C4040-V bearing: complete specifications & equivalents
The C4040-V is a ISO 15 radial bearing sized 200 x 310 x 109 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 200 mm |
| Outer diameter D | 310 mm |
| Width B | 109 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 1630 kN |
| Basic static load rating C0 | 2650 kN |
| Fatigue load limit Pu | 236 kN |
| Limiting speed (mechanical) | 260 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 30500 g |
| Manufacturer designation | C 4040 V |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & C4000-series range
| Bore d | 7.874 in |
|---|---|
| Outer diameter D | 12.205 in |
| Width B | 4.291 in |
| ISO bore code | 40 |
| Radial section height (D−d)/2 | 55 mm |
| Smallest bore in C4000-series | 50 mm |
| Largest outer diameter in C4000-series | 1030 mm |
| Width range across C4000-series | 30–315 mm |
| Bore position in C4000-series (smallest first) | 13 of 16 |
| Bore above smallest C4000-series size | 150 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24040 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 200×310×109 mm envelope as the SKF spherical roller bearing SKF 24040 CC/W33, but catalogue C/C0 differ (1630/2650 kN vs 1353/2120 kN) — and the functions differ: spherical locates axially, CARB floats. Pair them; never swap one-for-one. |
| 24040-CCK30-W33 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 200×310×109 mm envelope as the SKF spherical roller bearing SKF 24040 CCK30/W33, but catalogue C/C0 differ (1630/2650 kN vs 1353/2120 kN) — and the functions differ: spherical locates axially, CARB floats. Pair them; never swap one-for-one. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the C4040-V model number is decoded
C 4040 V belongs to the CARB family — compact aligning roller bearings: envelope 200×310×109 mm, radial rating 1630/2650 kN C/C0, and no axial-locating function by design. Reading the code: C marks the CARB toroidal family, the first two digits (40) identify the ISO dimension series and the last two (40) encode the 200 mm bore; suffixes describe bore and execution. The open execution relies on the housing seals and lubrication system, fed through groove/hole features on the large sizes. Explorer-class heat treatment and the crowned roller profile keep edge stress down when the 200 mm shaft deflects; no reference speed is listed and the limiting speed is 260 r/min. Float capacity is a selection criterion: the catalogue lists the permissible axial displacement (s) for the 109 mm wide set; size the free-end housing so thermal growth stays within it, not just inside the overall width. Open executions accept relubrication — route it through the outer-ring groove on sizes that have one and purge stale grease at service intervals. Grease through the annular groove features where provided; on open executions feed lubricant past the long roller set at assembly, since the 109 mm wide cavity does not fill itself.
Typical equipment & failure modes
Common applications
- heavy industrial gearbox layshafts used as the non-locating position
- winder and reel drums in paper and steel strip plants
- paper machine drying cylinders and calender rolls with long, thermally expanding shafts
- continuous-caster guide rolls and slab-caster segments under heat growth
Known failure patterns
- roller-end and flange smearing after lubricant starvation at the long roller contacts
- thermal preloading when a shaft is located at both ends and growth has nowhere to go
- brass cage pocket wear under marginal lubrication in the large-bore M/MB executions
- brinelling of washer raceways from impact or mounting force applied through the rolling elements
- oil starvation at the sliding contact zones of large spherical roller thrust bearings on forced-feed trips
Selection pitfalls — read before you substitute
- At 200 mm bore, shaft expansion is already measurable: calculate the required float inside the 109 mm wide bearing rather than assuming the free-end clearance is "enough" at operating temperature.
- The quoted 1630/2650 kN ratings belong to this exact execution (C 4040 V); VE240 vibrating-screen variants and sealed 2CS/2NS variants have their own figures even at the same envelope.
- Do not block the axial displacement in the drawing: housing covers, labyrinth rings and snap rings must leave the catalogue float (s) free, or the bearing silently becomes a poorly located fixed bearing.
- Envelope-identical spherical roller bearings (same ISO 15 d×D×B) are not drop-in equivalents — they locate the shaft axially, while C 4040 V must float; the two are designed to be used as a pair.
- Never use C 4040 V as the locating bearing: it carries no axial load by design — the arrangement needs a separate locating spherical, tapered or angular bearing facing the thrust.
- The 1630/2650 kN ratings and 30500 g mass are SKF catalogue values transcribed from ch. 10.1 of PUB BU/P1 17000 (PDF table page 864); mounting data — axial displacement (s) and seating details — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
What fails first on a misapplied CARB bearing?
Blocking the designed axial float — clamping the free end or locating both shaft ends — turns thermal growth into edge loading and spalls the toroidal raceways. Cage damage and ordinary fatigue follow overload or dry running.
Which dimensions does the C 4040 V have?
A C 4040 V measures 200 mm bore × 310 mm outside diameter × 109 mm width (7.874 × 12.205 × 4.291 in). From SKF catalogue PUB BU/P1 17000: dynamic C 1630 kN, static C0 2650 kN, fatigue limit Pu 236 kN, limiting speed 260 r/min, no reference speed listed, mass about 30500 g.
What does C 4040 V mean in SKF part numbering?
C marks CARB; 40 the dimension series; the size code gives 200 mm bore; V is the execution (cylindrical bore for direct shaft fitting, full-complement V execution (no cage)). The envelope follows ISO 15 and matches spherical roller bearing outlines, but the functions differ.
Why is C 4040 V used opposite a spherical roller bearing?
The spherical bearing locates the shaft and takes thrust; the CARB bearing at the other end self-aligns but floats, absorbing thermal expansion without inducing axial load. The pair is standard on paper machine drying cylinders and long caster rolls.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings on 2026-09-27. Read our editorial & correction policy.