NF208EA bearing: complete specifications & equivalents
The NF208EA is a ISO 15 radial bearing sized 40 x 80 x 18 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 40 mm |
| Outer diameter D | 80 mm |
| Width B | 18 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 66 kN |
| Basic static load rating C0 | 55.5 kN |
| Fatigue load limit Pu | 6.75 kN |
| Limiting speed (mechanical) | 8500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 365 g |
| Manufacturer designation | NTN NF208EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NF200-series range
| Bore d | 1.575 in |
|---|---|
| Outer diameter D | 3.15 in |
| Width B | 0.709 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 20 mm |
| Smallest bore in NF200-series | 20 mm |
| Largest outer diameter in NF200-series | 580 mm |
| Width range across NF200-series | 14–92 mm |
| Bore position in NF200-series (smallest first) | 5 of 34 |
| Bore above smallest NF200-series size | 20 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NF208EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NF208EA model number is decoded
NF208EA belongs to the NTN cylindrical roller range in NTN Ball and Roller Bearings CAT.No.2203E, under the ＊ ULTAGE new-generation specification: line-contact rollers between ground raceways for a 66 kN dynamic rating in the 40 mm bore. On the NTN nameplate NF states which ring carries the ribs, which determines whether NF208EA floats or locates; the numeric remainder is the ISO 15 series and 40 mm bore reference, not a fit or clearance instruction. EA marks the high-capacity design: optimised roller complement in a pressed (stamped) sheet-steel cage for more load capacity than the basic number in the same ISO 15 envelope; the ＊ symbol printed before the number in 2203E marks the ULTAGE new-generation specification — upgraded material/geometry and longer rating life, not part of the order code; quote the full NF208EA designation when purchasing. Mass 365 g for the 40×80×18 mm NF208EA execution covers the pressed-steel cage and full roller complement; substitute on mass plus rating, not envelope alone. Mount the separable inner ring + roller assembly on the shaft first and slide the outer ring into the housing; never press the outer ring through the rollers of NF208EA.
Typical equipment & failure modes
Common applications
- pump and compressor crankshafts and rotors
- machine-tool gearbox and spindle radial sets
- material-handling drum and wheel shafts
- papermaking and printing auxiliary drives
Known failure patterns
- roller smearing (microwelding) at start-up before the oil film builds under insufficient radial load
- cage wear accelerated when the EA high-capacity roller complement runs continuously above its thermal balance
- grease starvation and cage drag when relubrication intervals are extended past the grease life
- hard-particle indentation of raceways in unfiltered oil or open arrangements
- brinelling from static overload or impact during handling
Selection pitfalls — read before you substitute
- On this 40 mm bore, shaft thermal growth can preload the inner ring if the fit is too tight; verify residual interference at temperature and confirm the float ring still slides after mounting NF208EA.
- The EA high-capacity roller complement changes the load figure versus the basic execution of the same number; the 66/55.5 kN pair here belongs to NF208EA as printed, not to the bare size.
- If the shaft must be located both ways, do not use NF208EA alone: pair it with a locating bearing or specify the NUP execution with the matching loose rib ring from the 2203E table.
- The EA high-capacity roller complement changes the load figure versus the basic execution of the same number; the 66/55.5 kN pair here belongs to NF208EA as printed, not to the bare size.
- The 18 mm width and abutment faces must be square to the axis; a tilted spacer concentrates load across the roller set and shows as uneven raceway polish on the 40 mm inner ring.
- The 66/55.5 kN ratings, 6.75 kN Pu and 365 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NF208EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NF208EA?
NF208EA is an NTN NF single-row cylindrical roller bearing to ISO 15: 40 mm bore, 80 mm OD and 18 mm width (1.575 × 3.15 × 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 66 kN, C0 55.5 kN, Pu 6.75 kN, grease limiting speed 8,500 r/min, oil 12,000 r/min, mass about 365 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NF208EA is one integral rib on each ring — separable inner ring with single-direction axial guidance and a defined shaft position.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can NF208EA take axial load and locate a shaft?
the NF design gives one-direction axial guidance via its single outer-ring rib. The loose rib ring still only suits light/short-duration axial guidance; heavy thrust belongs to a dedicated thrust bearing.
What do Fw and Ew mean for NF208EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 49.5 mm, Ew 71.5 mm. The nominal bore/OD remain 40/80 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 8,500 r/min grease / 12,000 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.