NF2215EA bearing: complete specifications & equivalents
The NF2215EA is a ISO 15 radial bearing sized 75 x 130 x 31 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 75 mm |
| Outer diameter D | 130 mm |
| Width B | 31 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 191 kN |
| Basic static load rating C0 | 207 kN |
| Fatigue load limit Pu | 25 kN |
| Limiting speed (mechanical) | 4200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1610 g |
| Manufacturer designation | NTN NF2215EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NF2200-series range
| Bore d | 2.953 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 1.22 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in NF2200-series | 20 mm |
| Largest outer diameter in NF2200-series | 170 mm |
| Width range across NF2200-series | 18–43 mm |
| Bore position in NF2200-series (smallest first) | 12 of 16 |
| Bore above smallest NF2200-series size | 55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NF2215EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NF2215EA model number is decoded
In NTN Ball and Roller Bearings CAT.No.2203E, NF2215EA appears as a 75 mm bore single-row cylindrical roller bearing (191 kN C / 207 kN C0) with the EA high-capacity pressed sheet-steel cage, listed to the ISO 15 boundary plan. Reading the code: NF for the rib-on-each-ring type, then the ISO 15 diameter/width series and the bore code — ×5 = 75 mm (00–03 use the 10/12/15/17 exception table). The separable ring comes off without removing the roller assembly from the other ring, which eases inspection and lets the non-locating arrangement accommodate thermal shaft growth. Equivalent-load planning treats NF2215EA as a pure radial bearing: keep P below 191 kN at the required L10, and let a paired angular-contact or thrust part carry any sustained axial component. Heat the inner ring to max 120 °C for the 75 mm interference fit and support the ring face square during fitting; cocking over a keyway brinells the raceway before first rotation.
Typical equipment & failure modes
Common applications
- heavy industrial gearbox and reducer shafts
- large pump, turbine and compressor rotors
- rolling-mill auxiliary drive shafts
- crusher and vibrating-screen drive shafts
Known failure patterns
- inner-ring raceway spalling from overload in the line-contact Hertzian zone
- pressed-steel cage pocket wear when rollers skid at light load or too-thin lubricant
- micro-pitting when the EHL film falls below the composite roughness at high specific load
- false brinelling on standby machines exposed to external vibration
- edge loading from shaft deflection beyond the 3–4 arc-minute alignment limit
Selection pitfalls — read before you substitute
- Induction-heat the 75 mm inner ring (max 120 °C) and mount it before fitting the outer ring; the ring mass makes square guidance essential — driving through the rollers brinells the 130 mm raceway.
- The 31 mm width and abutment faces must be square to the axis; a tilted spacer concentrates load across the roller set and shows as uneven raceway polish on the 75 mm inner ring.
- The NF rib arrangement is not interchangeable with another prefix on the same 75 mm seat: one rib on each ring. Swapping NU for NJ changes axial location behaviour even though the 130×31 mm envelope matches.
- Do not replace NF2215EA with a deep-groove ball bearing on rating alone: line contact gives 191 kN radial capacity but the bearing cannot carry the thrust duty a ball bearing can and misalignment tolerance is only 3–4 arc-minutes.
- The EA high-capacity roller complement changes the load figure versus the basic execution of the same number; the 191/207 kN pair here belongs to NF2215EA as printed, not to the bare size.
- The 191/207 kN ratings, 25 kN Pu and 1610 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NF2215EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NF2215EA?
NF2215EA is an NTN NF single-row cylindrical roller bearing to ISO 15: 75 mm bore, 130 mm OD and 31 mm width (2.953 × 5.118 × 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 191 kN, C0 207 kN, Pu 25 kN, grease limiting speed 4,200 r/min, oil 5,900 r/min, mass about 1610 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NF2215EA is one integral rib on each ring — separable inner ring with single-direction axial guidance and a defined shaft position.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can NF2215EA take axial load and locate a shaft?
the NF design gives one-direction axial guidance via its single outer-ring rib. The loose rib ring still only suits light/short-duration axial guidance; heavy thrust belongs to a dedicated thrust bearing.
What do Fw and Ew mean for NF2215EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 88.5 mm, Ew 118.5 mm. The nominal bore/OD remain 75/130 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 4,200 r/min grease / 5,900 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.