NF2309EA bearing: complete specifications & equivalents
The NF2309EA is a ISO 15 radial bearing sized 45 x 100 x 36 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 45 mm |
| Outer diameter D | 100 mm |
| Width B | 36 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 162 kN |
| Basic static load rating C0 | 153 kN |
| Fatigue load limit Pu | 18.7 kN |
| Limiting speed (mechanical) | 5700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1300 g |
| Manufacturer designation | NTN NF2309EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NF2300-series range
| Bore d | 1.772 in |
|---|---|
| Outer diameter D | 3.937 in |
| Width B | 1.417 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in NF2300-series | 20 mm |
| Largest outer diameter in NF2300-series | 170 mm |
| Width range across NF2300-series | 21–58 mm |
| Bore position in NF2300-series (smallest first) | 6 of 13 |
| Bore above smallest NF2300-series size | 25 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NF2309EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NF2309EA model number is decoded
The NTN order number NF2309EA denotes a 45×100×36 mm (1.772 × 3.937 × 1.417 in) cylindrical roller bearing in the NF2300 family, the EA high-capacity pressed sheet-steel cage. Reading the code: NF for the rib-on-each-ring type, then the ISO 15 diameter/width series and the bore code — ×5 = 45 mm (00–03 use the 10/12/15/17 exception table). NTN ships these bearings open with normal (CN) radial clearance and P0 tolerance as standard; precision classes and C3/C4 clearance are separate order suffixes, not part of NF2309EA. Rating life at 162 kN C assumes clean oil and adequate film; the 18.7 kN Pu floor means contamination derating — not the C rating alone — governs adjusted life in dusty gearboxes. Mount the separable inner ring + roller assembly on the shaft first and slide the outer ring into the housing; never press the outer ring through the rollers of NF2309EA.
Typical equipment & failure modes
Common applications
- material-handling drum and wheel shafts
- papermaking and printing auxiliary drives
- fan and blower rotor positions
- industrial gearbox input and output shafts
Known failure patterns
- inner-ring raceway spalling from overload in the line-contact Hertzian zone
- cage distortion after a mounting blow carried through the roller set
- roller-end and raceway scoring from inadequate oil flow under heavy radial load
- fretting corrosion on a loose rotating shaft seat
- electrical pitting on VFD-driven motor shafts without grounding protection
Selection pitfalls — read before you substitute
- On this 45 mm bore, shaft thermal growth can preload the inner ring if the fit is too tight; verify residual interference at temperature and confirm the float ring still slides after mounting NF2309EA.
- The 36 mm width and abutment faces must be square to the axis; a tilted spacer concentrates load across the roller set and shows as uneven raceway polish on the 45 mm inner ring.
- Open NF2309EA units need application-supplied sealing and a defined lubricant schedule; film thickness is the first failure mode for line contact when viscosity drops at the 45 mm contact.
- The 36 mm width and abutment faces must be square to the axis; a tilted spacer concentrates load across the roller set and shows as uneven raceway polish on the 45 mm inner ring.
- Never press either ring through the roller complement when fitting: mounting force goes through the ring faces, or the 100 mm race brinells and releases as vibration within hours.
- The 162/153 kN ratings, 18.7 kN Pu and 1300 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NF2309EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NF2309EA?
NF2309EA is an NTN NF single-row cylindrical roller bearing to ISO 15: 45 mm bore, 100 mm OD and 36 mm width (1.772 × 3.937 × 1.417 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 162 kN, C0 153 kN, Pu 18.7 kN, grease limiting speed 5,700 r/min, oil 8,200 r/min, mass about 1300 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NF2309EA is one integral rib on each ring — separable inner ring with single-direction axial guidance and a defined shaft position.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can NF2309EA take axial load and locate a shaft?
the NF design gives one-direction axial guidance via its single outer-ring rib. The loose rib ring still only suits light/short-duration axial guidance; heavy thrust belongs to a dedicated thrust bearing.
What do Fw and Ew mean for NF2309EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 58.5 mm, Ew 88.5 mm. The nominal bore/OD remain 45/100 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 5,700 r/min grease / 8,200 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.