NJ2216-ECP bearing: complete specifications & equivalents
The NJ2216-ECP is a ISO 15 radial bearing sized 80 x 140 x 33 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 80 mm |
| Outer diameter D | 140 mm |
| Width B | 33 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 212 kN |
| Basic static load rating C0 | 245 kN |
| Fatigue load limit Pu | 31 kN |
| Reference speed (thermal) | 5300 rpm |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 2050 g |
| Manufacturer designation | SKF NJ 2216 ECP |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ2200-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 5.512 in |
| Width B | 1.299 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in NJ2200-series | 17 mm |
| Largest outer diameter in NJ2200-series | 480 mm |
| Width range across NJ2200-series | 16–130 mm |
| Bore position in NJ2200-series (smallest first) | 14 of 31 |
| Bore above smallest NJ2200-series size | 63 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NU2216-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×140×33 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NUP2216-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×140×33 mm and equivalent catalogue ratings; the NUP execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ2216-ECP model number is decoded
SKF NJ 2216 ECP is a single-row caged cylindrical roller bearing sized 80×140×33 mm — a dimension series 22 (light-section, wide), listed in SKF catalogue PUB BU/P1 17000 ch. 6.1. Reading the NJ prefix: two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. This makes the execution able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. Reading the order-string suffix ECP: the E-design execution with a glass-fibre reinforced polyamide (PA66) cage, limited to 120 °C continuous. Selection arithmetic: C0/C ≈ 1.16 (245 against 212 kN), and the Pu figure 31 kN is the fatigue load-limit floor for the SKF life equation; the catalogue lists 5,300 r/min thermal reference speed and 5,600 r/min mechanical limiting speed. Fit practice for NJ2216-ECP: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- heavy gearbox and pinion shafts
- large pump and blower rotors
- rolling-mill auxiliary drive shafts
- paper-machine press rolls
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- polymer cage softening above 120 °C
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- edge loading from shaft deflection beyond the bearing alignment limit (≈ 3-4 minutes of arc for single-row CRB)
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 22 (light-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2216, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 2216 ECP and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 33 mm-wide ring and concentrates load.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 140 mm raceway.
- The 212/245 kN ratings are SKF catalogue 17000 (2018) values for the ECP execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ2216-ECP?
SKF NJ 2216 ECP is a single-row caged cylindrical roller bearing with 80 mm bore, 140 mm OD and 33 mm width per ISO 15. SKF lists C 212 kN, C0 245 kN, Pu 31 kN, reference speed 5,300 r/min and limiting speed 5,600 r/min, mass about 2050 g.
What does the NJ designation and ECP suffix mean?
The ECP suffix marks the E-design execution with a glass-fibre reinforced polyamide (PA66) cage, limited to 120 °C continuous. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ2216-ECP take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ2216-ECP compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.