NJ2310EA bearing: complete specifications & equivalents
The NJ2310EA is a ISO 15 radial bearing sized 50 x 110 x 40 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 50 mm |
| Outer diameter D | 110 mm |
| Width B | 40 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 192 kN |
| Basic static load rating C0 | 187 kN |
| Fatigue load limit Pu | 22.7 kN |
| Limiting speed (mechanical) | 5200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1750 g |
| Manufacturer designation | NTN NJ2310EA |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & NJ2300-series range
| Bore d | 1.969 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 1.575 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in NJ2300-series | 20 mm |
| Largest outer diameter in NJ2300-series | 580 mm |
| Width range across NJ2300-series | 21–175 mm |
| Bore position in NJ2300-series (smallest first) | 7 of 31 |
| Bore above smallest NJ2300-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ2310EA | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ2310EA model number is decoded
NJ2310EA belongs to the NTN cylindrical roller range in NTN Ball and Roller Bearings CAT.No.2203E, under the ＊ ULTAGE new-generation specification: line-contact rollers between ground raceways for a 192 kN dynamic rating in the 50 mm bore. Digit by digit, NJ2310EA reads as NJ (inner ring two ribs + one outer rib), ISO 15 series, and bore 50 mm; trailing letters such as EA or E mark the cage/capacity execution and are part of the order number. The 30.0 mm radial section ((110−50)/2) frames the roller complement; capacity per millimetre of bore is about 3.8 kN/mm before application factors. The 50 mm (1.969 in) bore and 110 mm (4.331 in) OD are ISO 15 boundary values; fillet and shoulder dimensions must still come from the NTN mounting table for the 40 mm-wide ring. Heat the inner ring to max 120 °C for the 50 mm interference fit and support the ring face square during fitting; cocking over a keyway brinells the raceway before first rotation.
Typical equipment & failure modes
Common applications
- machine-tool gearbox and spindle radial sets
- material-handling drum and wheel shafts
- papermaking and printing auxiliary drives
- fan and blower rotor positions
Known failure patterns
- inner-ring raceway spalling from overload in the line-contact Hertzian zone
- pressed-steel cage pocket wear when rollers skid at light load or too-thin lubricant
- grease starvation and cage drag when relubrication intervals are extended past the grease life
- fretting corrosion on a loose rotating shaft seat
- rolling-contact fatigue after the catalogue L10 life is exceeded
Selection pitfalls — read before you substitute
- On this 50 mm bore, shaft thermal growth can preload the inner ring if the fit is too tight; verify residual interference at temperature and confirm the float ring still slides after mounting NJ2310EA.
- The 40 mm width and abutment faces must be square to the axis; a tilted spacer concentrates load across the roller set and shows as uneven raceway polish on the 50 mm inner ring.
- Grease limiting speed 5,200 r/min and oil 7,300 r/min are different limits for NJ2310EA: the first is the cage/lubricant mechanical ceiling, the second assumes real oil flow rather than an oil bath.
- Wide (22/23) and light (10/49) executions at 50 mm bore share bore but not OD/width; check the full NJ2300 series code before substituting, because housing and shoulder geometry will not interchange.
- The 30.0 mm section at 50 mm bore leaves a narrow oil path; with the EA pressed-steel-cage cage the relubrication groove and oil-level design must keep grease from churning in the 40 mm-wide cavity.
- The 192/187 kN ratings, 22.7 kN Pu and 1750 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for NJ2310EA (EA pressed-steel-cage execution); other makes sharing the ISO 15 envelope revise internal geometry without changing the order number, so keep the 2203E reference with the specification for critical drives.
Frequently asked questions
What are the dimensions and catalogue data of NJ2310EA?
NJ2310EA is an NTN NJ single-row cylindrical roller bearing to ISO 15: 50 mm bore, 110 mm OD and 40 mm width (1.969 × 4.331 × 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 192 kN, C0 187 kN, Pu 22.7 kN, grease limiting speed 5,200 r/min, oil 7,300 r/min, mass about 1750 g. It is open, with the EA high-capacity pressed sheet-steel cage.
What is the difference between NU, NJ, NUP, N and NF cylindrical roller bearings?
The prefix states the rib arrangement: NU has two outer-ring ribs and a ribless inner ring (float, no axial load); NJ adds ribs for one-direction location; NUP adds a loose L-ring to locate both directions; N has two inner-ring ribs and a separable outer ring; NF has one rib per ring for one-direction guidance. NJ2310EA is two integral ribs on the inner ring and one rib on the outer ring — it locates the shaft in one axial direction.
What do the EA, E and ＊ suffixes mean on NTN cylindrical roller bearings?
EA is NTN's high-capacity design with a pressed sheet-steel cage and optimised roller complement in the same ISO 15 envelope; E marks the high-capacity design at the larger bores; the ＊ symbol printed before the code in the NTN catalogue marks the ULTAGE new-generation specification and is not typed as part of the order number. This page's bearing carries the EA pressed-steel-cage execution.
Can NJ2310EA take axial load and locate a shaft?
the NJ design accepts axial load in one direction and provides one-way shaft location. For two-direction location use an NUP execution or an NJ pair with loose rib rings.
What do Fw and Ew mean for NJ2310EA?
Fw is the inner sub-assembly raceway/roller-set envelope diameter and Ew the outer-ring raceway diameter printed for geometric checks: Fw 65 mm, Ew 97 mm. The nominal bore/OD remain 50/110 mm; Fw/Ew describe the rolling-contact path, and speeds still run to 5,200 r/min grease / 7,300 r/min oil.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.