NJ2980-ECMA bearing: complete specifications & equivalents
The NJ2980-ECMA is a ISO 15 radial bearing sized 400 x 540 x 82 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 400 mm |
| Outer diameter D | 540 mm |
| Width B | 82 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1380 kN |
| Basic static load rating C0 | 2800 kN |
| Fatigue load limit Pu | 245 kN |
| Reference speed (thermal) | 1200 rpm |
| Limiting speed (mechanical) | 1600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 57000 g |
| Manufacturer designation | SKF NJ 2980 ECMA |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ2900-series range
| Bore d | 15.748 in |
|---|---|
| Outer diameter D | 21.26 in |
| Width B | 3.228 in |
| ISO bore code | 80 |
| Radial section height (D−d)/2 | 70 mm |
| Smallest bore in NJ2900-series | 340 mm |
| Largest outer diameter in NJ2900-series | 850 mm |
| Width range across NJ2900-series | 72–128 mm |
| Bore position in NJ2900-series (smallest first) | 2 of 5 |
| Bore above smallest NJ2900-series size | 60 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NJ2980-ECMA model number is decoded
Ordering number SKF NJ 2980 ECMA resolves to a 400×540×82 mm single-row caged cylindrical roller bearing (dimension series 29 (compact OD, normal width)); two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. Structurally, the NJ design has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. In arrangement terms it is able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. Reading the order-string suffix ECMA: the E-design ECMA execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Speed planning for NJ2980-ECMA: the catalogue lists 1,200 r/min thermal reference speed and 1,600 r/min mechanical limiting speed. The mass entry 57000 g covers the complete catalogue execution. Fit practice for NJ2980-ECMA: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- mining hoist and winder shafts
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- hard-particle indentation of the raceway in unfiltered oil systems
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 29 (compact OD, normal width) envelope is shared with the N/NU/NJ/NUP executions of 2980, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 2980 ECMA and do not substitute rib styles without checking the shaft locating scheme.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 540 mm raceway.
- The 1380/2800 kN ratings are SKF catalogue 17000 (2018) values for the ECMA execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ2980-ECMA?
SKF NJ 2980 ECMA is a single-row caged cylindrical roller bearing with 400 mm bore, 540 mm OD and 82 mm width per ISO 15. SKF lists C 1380 kN, C0 2800 kN, Pu 245 kN, reference speed 1,200 r/min and limiting speed 1,600 r/min, mass about 57000 g.
What does the NJ designation and ECMA suffix mean?
The ECMA suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ2980-ECMA take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ2980-ECMA compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.