NJ336-ECM bearing: complete specifications & equivalents
The NJ336-ECM is a ISO 15 radial bearing sized 180 x 380 x 75 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 180 mm |
| Outer diameter D | 380 mm |
| Width B | 75 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1020 kN |
| Basic static load rating C0 | 1290 kN |
| Fatigue load limit Pu | 125 kN |
| Reference speed (thermal) | 1600 rpm |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 44000 g |
| Manufacturer designation | SKF NJ 336 ECM |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ300-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 14.961 in |
| Width B | 2.953 in |
| ISO bore code | 36 |
| Radial section height (D−d)/2 | 100 mm |
| Smallest bore in NJ300-series | 17 mm |
| Largest outer diameter in NJ300-series | 500 mm |
| Width range across NJ300-series | 14–95 mm |
| Bore position in NJ300-series (smallest first) | 26 of 29 |
| Bore above smallest NJ300-series size | 163 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NU336-ECM | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 180×380×75 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ336-ECM model number is decoded
SKF NJ 336 ECM is a single-row caged cylindrical roller bearing sized 180×380×75 mm — a dimension series 3 (medium-section ISO 15 envelope), listed in SKF catalogue PUB BU/P1 17000 ch. 6.1. Structurally, the NJ design has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. In arrangement terms it is able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. Reading the order-string suffix ECM: the E-design ECM execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Speed planning for NJ336-ECM: the catalogue lists 1,600 r/min thermal reference speed and 2,200 r/min mechanical limiting speed. The mass entry 44000 g covers the complete catalogue execution. Fit practice for NJ336-ECM: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- mining hoist and winder shafts
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- brinelling from static overload or impact during handling and mounting
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 3 (medium-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 336, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 336 ECM and do not substitute rib styles without checking the shaft locating scheme.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 380 mm raceway.
- The 1020/1290 kN ratings are SKF catalogue 17000 (2018) values for the ECM execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ336-ECM?
SKF NJ 336 ECM is a single-row caged cylindrical roller bearing with 180 mm bore, 380 mm OD and 75 mm width per ISO 15. SKF lists C 1020 kN, C0 1290 kN, Pu 125 kN, reference speed 1,600 r/min and limiting speed 2,200 r/min, mass about 44000 g.
What does the NJ designation and ECM suffix mean?
The ECM suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ336-ECM take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ336-ECM compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.