NNCF4916-CV bearing: complete specifications & equivalents
The NNCF4916-CV is a ISO 15 radial bearing sized 80 x 110 x 30 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 80 mm |
| Outer diameter D | 110 mm |
| Width B | 30 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 121 kN |
| Basic static load rating C0 | 216 kN |
| Fatigue load limit Pu | 25 kN |
| Reference speed (thermal) | 2600 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 870 g |
| Manufacturer designation | SKF NNCF 4916 CV |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NNCF4900-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 1.181 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 15 mm |
| Smallest bore in NNCF4900-series | 60 mm |
| Largest outer diameter in NNCF4900-series | 540 mm |
| Width range across NNCF4900-series | 25–140 mm |
| Bore position in NNCF4900-series (smallest first) | 3 of 25 |
| Bore above smallest NNCF4900-series size | 20 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NNC4916-CV | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×110×30 mm and equivalent catalogue ratings; the NNC execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NNCL4916-CV | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 80×110×30 mm and equivalent catalogue ratings; the NNCL execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NNCF4916-CV model number is decoded
NNCF4916-CV is the 80 mm bore entry in the NNCF4900 range: a 80×110×30 mm double-row full-complement cylindrical roller bearing with a full complement of extra rollers fitted in place of a cage, rated C 121 kN / C0 216 kN. Structurally, the NNCF design has a non-separable double-row full complement bearing with three integral flanges on the inner ring and one retaining ring in the outer ring; the outer ring also has an annular lubrication groove with holes. In arrangement terms it is one-direction locating: the retained outer ring guides the shaft axially in one direction. Reading the order-string suffix CV: the full-complement execution — extra rollers replace the cage, trading speed for maximum radial capacity and stiffness. Load-per-bore for the 80 mm seat is about 1.51 kN/mm, typical of dimension series 49 (compact heavy section); use C0 216 kN for static checks such as crane hook blocks standing under load. Mounting: the retaining ring must never be loaded axially in operation; route relubrication through the outer-ring groove and keep the unit non-separable during handling. A 80 mm seat normally takes a k5 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- rolling-mill and caster drives
- large crane and winch drums
- offshore crane sheaves
- heavy material-handling rope pulleys
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- roller smearing between the uncaged rollers during slow skidding starts under heavy static load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- uneven row loading from misalignment, concentrating fatigue on one row of the double complement
- electrical pitting on VFD-driven shafts without grounding protection
Selection pitfalls — read before you substitute
- The NNCF/NNCL/NNC triplet shares the envelope and ratings but differs in outer-ring retention — one retaining ring, none, or two; selecting the wrong one changes the axial-locating scheme.
- Relubrication must reach both roller rows through the annular groove; blocked lube holes starve one row silently and show later as asymmetric raceway wear.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 121/216 kN ratings are SKF catalogue 17000 (2018) values for the CV execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NNCF4916-CV?
SKF NNCF 4916 CV is a double-row full-complement cylindrical roller bearing with 80 mm bore, 110 mm OD and 30 mm width per ISO 15. SKF lists C 121 kN, C0 216 kN, Pu 25 kN, reference speed 2,600 r/min and limiting speed 3,400 r/min, mass about 870 g.
What does the NNCF designation and CV suffix mean?
Suffix CV identifies the full-complement execution: the space a cage would occupy is filled with extra rollers, trading speed for maximum radial capacity and stiffness. Structurally this execution has a non-separable double-row full complement bearing with three integral flanges on the inner ring and one retaining ring in the outer ring; the outer ring also has an annular lubrication groove with holes.
Can NNCF4916-CV take axial load and locate the shaft?
In one direction, via the retained outer ring; the retaining ring is not a load path for continuous thrust.
How does NNCF4916-CV compare with the other executions in the same envelope?
NNCF (one outer retaining ring, one-direction guidance), NNCL (no retaining ring, floating outer ring) and NNC (retaining rings both sides, two-direction location) share the ISO envelope and ratings but are not interchangeable in a locating arrangement.
What limits the service life of this bearing most often?
On full-complement bearings the dominant risks are roller smearing from skidding below minimum load and contamination; maintain minimum radial load, keep lubricant film thick and accelerate gently.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.