NNCL4860-CV bearing: complete specifications & equivalents
The NNCL4860-CV is a ISO 15 radial bearing sized 300 x 380 x 80 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 300 mm |
| Outer diameter D | 380 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 858 kN |
| Basic static load rating C0 | 2120 kN |
| Fatigue load limit Pu | 196 kN |
| Reference speed (thermal) | 700 rpm |
| Limiting speed (mechanical) | 850 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 22000 g |
| Manufacturer designation | SKF NNCL 4860 CV |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NNCL4800-series range
| Bore d | 11.811 in |
|---|---|
| Outer diameter D | 14.961 in |
| Width B | 3.15 in |
| ISO bore code | 60 |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in NNCL4800-series | 150 mm |
| Largest outer diameter in NNCL4800-series | 500 mm |
| Width range across NNCL4800-series | 40–100 mm |
| Bore position in NNCL4800-series (smallest first) | 11 of 16 |
| Bore above smallest NNCL4800-series size | 150 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NNC4860-CV | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 300×380×80 mm and equivalent catalogue ratings; the NNC execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NNCF4860-CV | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 300×380×80 mm and equivalent catalogue ratings; the NNCF execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NNCL4860-CV model number is decoded
For a 300 mm shaft, SKF lists NNCL4860-CV as double-row full-complement cylindrical roller: 380 mm OD, 80 mm wide, Pu 196 kN, the catalogue lists 700 r/min thermal reference speed and 850 r/min mechanical limiting speed. Structurally, the NNCL design has a double-row full complement bearing with three integral flanges on the inner ring and no retaining ring in the smooth outer ring, which is free to pass over the roller set. In arrangement terms it is non-locating: the outer ring can be displaced axially, like an NN design, to absorb shaft expansion. Suffix CV identifies the full-complement execution: the space a cage would occupy is filled with extra rollers, trading speed for maximum radial capacity and stiffness. The full complement of extra rollers fitted in place of a cage is reflected in the published speeds and temperature limits. Selection arithmetic: C0/C ≈ 2.47 (2120 against 858 kN), and the Pu figure 196 kN is the fatigue load-limit floor for the SKF life equation; the catalogue lists 700 r/min thermal reference speed and 850 r/min mechanical limiting speed. Assembly note: treat the outer ring as the floating element; keep the inner ring with its three flanges square on the shaft and relubricate through the outer-ring groove. Heat steel rings inductively to max 120 °C, and never wash a full-complement unit in a way that displaces rollers.
Typical equipment & failure modes
Common applications
- steelmaking and heavy crane sheaves
- large offshore winch and hook blocks
- mining shovel and dragline pivots
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- roller smearing between the uncaged rollers during slow skidding starts under heavy static load
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- uneven row loading from misalignment, concentrating fatigue on one row of the double complement
- fretting corrosion on a loose rotating shaft seat or in a vibratory stand-still
Selection pitfalls — read before you substitute
- The NNCF/NNCL/NNC triplet shares the envelope and ratings but differs in outer-ring retention — one retaining ring, none, or two; selecting the wrong one changes the axial-locating scheme.
- Relubrication must reach both roller rows through the annular groove; blocked lube holes starve one row silently and show later as asymmetric raceway wear.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 380 mm raceway.
- The 858/2120 kN ratings are SKF catalogue 17000 (2018) values for the CV execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NNCL4860-CV?
SKF NNCL 4860 CV is a double-row full-complement cylindrical roller bearing with 300 mm bore, 380 mm OD and 80 mm width per ISO 15. SKF lists C 858 kN, C0 2120 kN, Pu 196 kN, reference speed 700 r/min and limiting speed 850 r/min, mass about 22000 g.
What does the NNCL designation and CV suffix mean?
Suffix CV identifies the full-complement execution: the space a cage would occupy is filled with extra rollers, trading speed for maximum radial capacity and stiffness. Structurally this execution has a double-row full complement bearing with three integral flanges on the inner ring and no retaining ring in the smooth outer ring, which is free to pass over the roller set.
Can NNCL4860-CV take axial load and locate the shaft?
No — the smooth outer ring floats, making NNCL the non-locating member of the arrangement.
How does NNCL4860-CV compare with the other executions in the same envelope?
NNCF (one outer retaining ring, one-direction guidance), NNCL (no retaining ring, floating outer ring) and NNC (retaining rings both sides, two-direction location) share the ISO envelope and ratings but are not interchangeable in a locating arrangement.
What limits the service life of this bearing most often?
On full-complement bearings the dominant risks are roller smearing from skidding below minimum load and contamination; maintain minimum radial load, keep lubricant film thick and accelerate gently.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.4 double-row full complement cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.