NU20-530-ECMA bearing: complete specifications & equivalents
The NU20-530-ECMA is a ISO 15 radial bearing sized 530 x 780 x 145 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 530 mm |
| Outer diameter D | 780 mm |
| Width B | 145 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 3740 kN |
| Basic static load rating C0 | 7350 kN |
| Fatigue load limit Pu | 550 kN |
| Reference speed (thermal) | 670 rpm |
| Limiting speed (mechanical) | 1000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 253000 g |
| Manufacturer designation | SKF NU 20/530 ECMA |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NU2000-series range
| Bore d | 20.866 in |
|---|---|
| Outer diameter D | 30.709 in |
| Width B | 5.709 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 125 mm |
| Smallest bore in NU2000-series | 300 mm |
| Largest outer diameter in NU2000-series | 1220 mm |
| Width range across NU2000-series | 95–212 mm |
| Bore position in NU2000-series (smallest first) | 5 of 12 |
| Bore above smallest NU2000-series size | 230 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NU20-530-ECMA model number is decoded
NU20-530-ECMA is the 530 mm bore entry in the NU2000 range: a 530×780×145 mm single-row caged cylindrical roller bearing with a one-piece machined brass cage, rated C 3740 kN / C0 7350 kN. Reading the NU prefix: two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable. This makes the execution non-locating: the inner ring assembly can float axially in both directions and the bearing cannot support axial load. The ECMA suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. The radial section height is 125.0 mm and the catalogue mass 253000 g; at 3740 kN dynamic rating this is roughly 7.06 kN of C per millimetre of bore before application factors. Assembly note: fit the inner ring and roller assembly onto the shaft and the outer ring into the housing independently; thermal expansion is absorbed by axial float, so do not trap the inner ring between shaft shoulders. Heat steel rings inductively to max 120 °C.
Typical equipment & failure modes
Common applications
- marine propulsion line shafts
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
- offshore drawworks shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- fretting corrosion on a loose rotating shaft seat or in a vibratory stand-still
Selection pitfalls — read before you substitute
- Do not use a NU bearing where axial load must be carried — the design carries radial load only
- The dimension series 20 (light section for large shafts) envelope is shared with the N/NU/NJ/NUP executions of 20/530, but flange configuration and axial-locating behaviour differ — quote the full SKF NU 20/530 ECMA and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 145 mm-wide ring and concentrates load.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 3740/7350 kN ratings are SKF catalogue 17000 (2018) values for the ECMA execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NU20-530-ECMA?
SKF NU 20/530 ECMA is a single-row caged cylindrical roller bearing with 530 mm bore, 780 mm OD and 145 mm width per ISO 15. SKF lists C 3740 kN, C0 7350 kN, Pu 550 kN, reference speed 670 r/min and limiting speed 1,000 r/min, mass about 253000 g.
What does the NU designation and ECMA suffix mean?
The ECMA suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable.
Can NU20-530-ECMA take axial load and locate the shaft?
No — the inner ring has no flanges, so the NU bearing is non-locating and carries radial load only; use NJ (one direction), NUP (both directions) or a paired thrust bearing for axial duty.
How does NU20-530-ECMA compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.