NU20-750-ECMA bearing: complete specifications & equivalents
The NU20-750-ECMA is a ISO 15 radial bearing sized 750 x 1090 x 195 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 750 mm |
| Outer diameter D | 1090 mm |
| Width B | 195 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 7040 kN |
| Basic static load rating C0 | 14600 kN |
| Fatigue load limit Pu | 980 kN |
| Reference speed (thermal) | 430 rpm |
| Limiting speed (mechanical) | 670 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 635000 g |
| Manufacturer designation | SKF NU 20/750 ECMA |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NU2000-series range
| Bore d | 29.528 in |
|---|---|
| Outer diameter D | 42.913 in |
| Width B | 7.677 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 170 mm |
| Smallest bore in NU2000-series | 300 mm |
| Largest outer diameter in NU2000-series | 1220 mm |
| Width range across NU2000-series | 95–212 mm |
| Bore position in NU2000-series (smallest first) | 10 of 12 |
| Bore above smallest NU2000-series size | 450 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NU20-750-ECMA model number is decoded
Ordering number SKF NU 20/750 ECMA resolves to a 750×1090×195 mm single-row caged cylindrical roller bearing (dimension series 20 (light section for large shafts)); two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable. Reading the NU prefix: two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable. This makes the execution non-locating: the inner ring assembly can float axially in both directions and the bearing cannot support axial load. Reading the order-string suffix ECMA: the E-design ECMA execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Selection arithmetic: C0/C ≈ 2.07 (14600 against 7040 kN), and the Pu figure 980 kN is the fatigue load-limit floor for the SKF life equation; the catalogue lists 430 r/min thermal reference speed and 670 r/min mechanical limiting speed. Fit practice for NU20-750-ECMA: fit the inner ring and roller assembly onto the shaft and the outer ring into the housing independently; thermal expansion is absorbed by axial float, so do not trap the inner ring between shaft shoulders. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- large rolling-mill drive trains
- marine propulsion line shafts
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- Do not use a NU bearing where axial load must be carried — the design carries radial load only
- The dimension series 20 (light section for large shafts) envelope is shared with the N/NU/NJ/NUP executions of 20/750, but flange configuration and axial-locating behaviour differ — quote the full SKF NU 20/750 ECMA and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 195 mm-wide ring and concentrates load.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 1090 mm raceway.
- The 7040/14600 kN ratings are SKF catalogue 17000 (2018) values for the ECMA execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NU20-750-ECMA?
SKF NU 20/750 ECMA is a single-row caged cylindrical roller bearing with 750 mm bore, 1090 mm OD and 195 mm width per ISO 15. SKF lists C 7040 kN, C0 14600 kN, Pu 980 kN, reference speed 430 r/min and limiting speed 670 r/min, mass about 635000 g.
What does the NU designation and ECMA suffix mean?
The ECMA suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable.
Can NU20-750-ECMA take axial load and locate the shaft?
No — the inner ring has no flanges, so the NU bearing is non-locating and carries radial load only; use NJ (one direction), NUP (both directions) or a paired thrust bearing for axial duty.
How does NU20-750-ECMA compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.