NU2360-ECMA bearing: complete specifications & equivalents
The NU2360-ECMA is a ISO 15 radial bearing sized 300 x 620 x 185 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 300 mm |
| Outer diameter D | 620 mm |
| Width B | 185 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 4020 kN |
| Basic static load rating C0 | 5850 kN |
| Fatigue load limit Pu | 480 kN |
| Reference speed (thermal) | 950 rpm |
| Limiting speed (mechanical) | 1600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 270000 g |
| Manufacturer designation | SKF NU 2360 ECMA |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NU2300-series range
| Bore d | 11.811 in |
|---|---|
| Outer diameter D | 24.409 in |
| Width B | 7.283 in |
| ISO bore code | 60 |
| Radial section height (D−d)/2 | 160 mm |
| Smallest bore in NU2300-series | 20 mm |
| Largest outer diameter in NU2300-series | 750 mm |
| Width range across NU2300-series | 21–224 mm |
| Bore position in NU2300-series (smallest first) | 32 of 35 |
| Bore above smallest NU2300-series size | 280 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NU2360-ECMA model number is decoded
NU2360-ECMA is the 300 mm bore entry in the NU2300 range: a 300×620×185 mm single-row caged cylindrical roller bearing with a one-piece machined brass cage, rated C 4020 kN / C0 5850 kN. Reading the NU prefix: two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable. This makes the execution non-locating: the inner ring assembly can float axially in both directions and the bearing cannot support axial load. The ECMA suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. The one-piece machined brass cage is reflected in the published speeds and temperature limits. The radial section height is 160.0 mm and the catalogue mass 270000 g; at 4020 kN dynamic rating this is roughly 13.40 kN of C per millimetre of bore before application factors. Mounting: fit the inner ring and roller assembly onto the shaft and the outer ring into the housing independently; thermal expansion is absorbed by axial float, so do not trap the inner ring between shaft shoulders. A 300 mm seat normally takes a m6 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- marine propulsion line shafts
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
- offshore drawworks shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- Do not use a NU bearing where axial load must be carried — the design carries radial load only
- The dimension series 23 (medium-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2360, but flange configuration and axial-locating behaviour differ — quote the full SKF NU 2360 ECMA and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 185 mm-wide ring and concentrates load.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 185 mm-wide ring and concentrates load.
- The 4020/5850 kN ratings are SKF catalogue 17000 (2018) values for the ECMA execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NU2360-ECMA?
SKF NU 2360 ECMA is a single-row caged cylindrical roller bearing with 300 mm bore, 620 mm OD and 185 mm width per ISO 15. SKF lists C 4020 kN, C0 5850 kN, Pu 480 kN, reference speed 950 r/min and limiting speed 1,600 r/min, mass about 270000 g.
What does the NU designation and ECMA suffix mean?
The ECMA suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable.
Can NU2360-ECMA take axial load and locate the shaft?
No — the inner ring has no flanges, so the NU bearing is non-locating and carries radial load only; use NJ (one direction), NUP (both directions) or a paired thrust bearing for axial duty.
How does NU2360-ECMA compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.