NU332-ECML bearing: complete specifications & equivalents
The NU332-ECML is a ISO 15 radial bearing sized 160 x 340 x 68 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 160 mm |
| Outer diameter D | 340 mm |
| Width B | 68 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1000 kN |
| Basic static load rating C0 | 1080 kN |
| Fatigue load limit Pu | 112 kN |
| Reference speed (thermal) | 2000 rpm |
| Limiting speed (mechanical) | 3600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 31000 g |
| Manufacturer designation | SKF NU 332 ECML |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NU300-series range
| Bore d | 6.299 in |
|---|---|
| Outer diameter D | 13.386 in |
| Width B | 2.677 in |
| ISO bore code | 32 |
| Radial section height (D−d)/2 | 90 mm |
| Smallest bore in NU300-series | 17 mm |
| Largest outer diameter in NU300-series | 620 mm |
| Width range across NU300-series | 14–109 mm |
| Bore position in NU300-series (smallest first) | 25 of 33 |
| Bore above smallest NU300-series size | 143 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ332-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 160×340×68 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NU332-ECML model number is decoded
For a 160 mm shaft, SKF lists NU332-ECML as single-row caged cylindrical roller: 340 mm OD, 68 mm wide, Pu 112 kN, the catalogue lists 2,000 r/min thermal reference speed and 3,600 r/min mechanical limiting speed. Reading the NU prefix: two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable. This makes the execution non-locating: the inner ring assembly can float axially in both directions and the bearing cannot support axial load. Reading the order-string suffix ECML: the E-design ECML execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Speed planning for NU332-ECML: the catalogue lists 2,000 r/min thermal reference speed and 3,600 r/min mechanical limiting speed. The mass entry 31000 g covers the complete catalogue execution. Mounting: fit the inner ring and roller assembly onto the shaft and the outer ring into the housing independently; thermal expansion is absorbed by axial float, so do not trap the inner ring between shaft shoulders. A 160 mm seat normally takes a m6 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- mining hoist and winder shafts
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- brinelling from static overload or impact during handling and mounting
Selection pitfalls — read before you substitute
- Do not use a NU bearing where axial load must be carried — the design carries radial load only
- The dimension series 3 (medium-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 332, but flange configuration and axial-locating behaviour differ — quote the full SKF NU 332 ECML and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 68 mm-wide ring and concentrates load.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 1000/1080 kN ratings are SKF catalogue 17000 (2018) values for the ECML execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NU332-ECML?
SKF NU 332 ECML is a single-row caged cylindrical roller bearing with 160 mm bore, 340 mm OD and 68 mm width per ISO 15. SKF lists C 1000 kN, C0 1080 kN, Pu 112 kN, reference speed 2,000 r/min and limiting speed 3,600 r/min, mass about 31000 g.
What does the NU designation and ECML suffix mean?
The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring and no flanges on the inner ring, so the inner ring together with the roller set is separable.
Can NU332-ECML take axial load and locate the shaft?
No — the inner ring has no flanges, so the NU bearing is non-locating and carries radial load only; use NJ (one direction), NUP (both directions) or a paired thrust bearing for axial duty.
How does NU332-ECML compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.