NUH2220-ECMH bearing: complete specifications & equivalents
The NUH2220-ECMH is a ISO 15 radial bearing sized 100 x 180 x 46 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 100 mm |
| Outer diameter D | 180 mm |
| Width B | 46 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 400 kN |
| Basic static load rating C0 | 475 kN |
| Fatigue load limit Pu | 57 kN |
| Reference speed (thermal) | 4000 rpm |
| Limiting speed (mechanical) | 4500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 5100 g |
| Manufacturer designation | SKF NUH 2220 ECMH |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUH2200-series range
| Bore d | 3.937 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 1.811 in |
| ISO bore code | 20 |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in NUH2200-series | 100 mm |
| Largest outer diameter in NUH2200-series | 440 mm |
| Width range across NUH2200-series | 46–120 mm |
| Bore position in NUH2200-series (smallest first) | 1 of 13 |
| Bore above smallest NUH2200-series size | 0 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NUH2220-ECMH model number is decoded
Ordering number SKF NUH 2220 ECMH resolves to a 100×180×46 mm high-capacity cylindrical roller bearing (dimension series 22 (light-section, wide)); a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring. The NUH configuration means a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring; functionally the bearing is the locating partner in paired cross-locating arrangements for heavily loaded shafts, locating axially in one direction. The ECMH suffix denotes the high-capacity execution with a machined brass cage; the /PEX variant is the pinion-shaft special build. Speed planning for NUH2220-ECMH: the catalogue lists 4,000 r/min thermal reference speed and 4,500 r/min mechanical limiting speed. The mass entry 5100 g covers the complete catalogue execution. Mounting: typically paired with the matching NCF ECJB non-locating bearing on the same shaft; observe the catalogue shoulder and fillet data for the large inner ring. A 100 mm seat normally takes a k5 interference with an H6 housing bore when the inner ring rotates. This is the standard catalogue execution of the high-capacity design. Selected sizes in the range are also produced as /PEX pinion-shaft builds for wind-turbine gearboxes — separate order numbers with their own rating lines and internal profiling; the two must not be mixed using one another’s loads.
Typical equipment & failure modes
Common applications
- wind-turbine rotor pinion shafts
- heavy mining and cement gear drives
- wind turbine gearbox planetary and intermediate shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- micro-pitting on the profiled rollers under contaminated or starved-lubricant conditions despite the black-oxide treatment
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- cage fatigue in heavily reversing wind-turbine load cycles when relubrication intervals are exceeded
- electrical pitting on VFD-driven shafts without grounding protection
Selection pitfalls — read before you substitute
- High-capacity NUH and NCF bearings are designed as a locating/non-locating PAIR on the same shaft; fitting two locating NUH bearings can preload the arrangement thermally.
- The /PEX pinion execution carries its own rating line and internal geometry — never substitute a standard NUH 2220 using the /PEX loads.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 180 mm raceway.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 180 mm raceway.
- The 400/475 kN ratings are SKF catalogue 17000 (2018) values for the ECMH execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUH2220-ECMH?
SKF NUH 2220 ECMH is a high-capacity cylindrical roller bearing with 100 mm bore, 180 mm OD and 46 mm width per ISO 15. SKF lists C 400 kN, C0 475 kN, Pu 57 kN, reference speed 4,000 r/min and limiting speed 4,500 r/min, mass about 5100 g.
What does the NUH designation and ECMH suffix mean?
The ECMH suffix denotes the high-capacity execution with a machined brass cage; the /PEX variant is the pinion-shaft special build. Structurally this execution has a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring.
Can NUH2220-ECMH take axial load and locate the shaft?
In one direction, as the locating member of a high-capacity pair; the matching NCF ECJB bearing floats. It is not a general-purpose axial bearing.
How does NUH2220-ECMH compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.