NUH2348-ECMH bearing: complete specifications & equivalents
The NUH2348-ECMH is a ISO 15 radial bearing sized 240 x 500 x 155 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 240 mm |
| Outer diameter D | 500 mm |
| Width B | 155 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 2750 kN |
| Basic static load rating C0 | 4000 kN |
| Fatigue load limit Pu | 345 kN |
| Reference speed (thermal) | 1200 rpm |
| Limiting speed (mechanical) | 1500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 143000 g |
| Manufacturer designation | SKF NUH 2348 ECMH |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUH2300-series range
| Bore d | 9.449 in |
|---|---|
| Outer diameter D | 19.685 in |
| Width B | 6.102 in |
| ISO bore code | 48 |
| Radial section height (D−d)/2 | 130 mm |
| Smallest bore in NUH2300-series | 100 mm |
| Largest outer diameter in NUH2300-series | 500 mm |
| Width range across NUH2300-series | 73–155 mm |
| Bore position in NUH2300-series (smallest first) | 13 of 13 |
| Bore above smallest NUH2300-series size | 140 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NUH2348-ECMH-PEX | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same ISO 15 envelope 240×500×155 mm, but catalogue C/C0 ratings differ between executions (2750/4000 vs 3150/4000 kN) and the NUH flange/ring configuration differs — envelope match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NUH2348-ECMH model number is decoded
Ordering number SKF NUH 2348 ECMH resolves to a 240×500×155 mm high-capacity cylindrical roller bearing (dimension series 23 (medium-section, wide)); a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring. Reading the NUH prefix: a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring. This makes the execution the locating partner in paired cross-locating arrangements for heavily loaded shafts, locating axially in one direction. The ECMH suffix denotes the high-capacity execution with a machined brass cage; the /PEX variant is the pinion-shaft special build. Load-per-bore for the 240 mm seat is about 11.46 kN/mm, typical of dimension series 23 (medium-section, wide); use C0 4000 kN for static checks such as crane hook blocks standing under load. Fit practice for NUH2348-ECMH: typically paired with the matching NCF ECJB non-locating bearing on the same shaft; observe the catalogue shoulder and fillet data for the large inner ring. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment. This is the standard catalogue execution of the high-capacity design. Selected sizes in the range are also produced as /PEX pinion-shaft builds for wind-turbine gearboxes — separate order numbers with their own rating lines and internal profiling; the two must not be mixed using one another’s loads.
Typical equipment & failure modes
Common applications
- offshore and marine heavy drive trains
- large mining mill pinion shafts
- multi-megawatt wind turbine main gearboxes
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- micro-pitting on the profiled rollers under contaminated or starved-lubricant conditions despite the black-oxide treatment
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- cage fatigue in heavily reversing wind-turbine load cycles when relubrication intervals are exceeded
- edge loading from shaft deflection beyond the bearing alignment limit (≈ 3-4 minutes of arc for single-row CRB)
Selection pitfalls — read before you substitute
- High-capacity NUH and NCF bearings are designed as a locating/non-locating PAIR on the same shaft; fitting two locating NUH bearings can preload the arrangement thermally.
- The /PEX pinion execution carries its own rating line and internal geometry — never substitute a standard NUH 2348 using the /PEX loads.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 155 mm-wide ring and concentrates load.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 155 mm-wide ring and concentrates load.
- The 2750/4000 kN ratings are SKF catalogue 17000 (2018) values for the ECMH execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUH2348-ECMH?
SKF NUH 2348 ECMH is a high-capacity cylindrical roller bearing with 240 mm bore, 500 mm OD and 155 mm width per ISO 15. SKF lists C 2750 kN, C0 4000 kN, Pu 345 kN, reference speed 1,200 r/min and limiting speed 1,500 r/min, mass about 143000 g.
What does the NUH designation and ECMH suffix mean?
The ECMH suffix denotes the high-capacity execution with a machined brass cage; the /PEX variant is the pinion-shaft special build. Structurally this execution has a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring.
Can NUH2348-ECMH take axial load and locate the shaft?
In one direction, as the locating member of a high-capacity pair; the matching NCF ECJB bearing floats. It is not a general-purpose axial bearing.
How does NUH2348-ECMH compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.