NUP2324-ECML bearing: complete specifications & equivalents
The NUP2324-ECML is a ISO 15 radial bearing sized 120 x 260 x 86 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 120 mm |
| Outer diameter D | 260 mm |
| Width B | 86 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 915 kN |
| Basic static load rating C0 | 1040 kN |
| Fatigue load limit Pu | 116 kN |
| Reference speed (thermal) | 2800 rpm |
| Limiting speed (mechanical) | 5000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 23500 g |
| Manufacturer designation | SKF NUP 2324 ECML |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUP2300-series range
| Bore d | 4.724 in |
|---|---|
| Outer diameter D | 10.236 in |
| Width B | 3.386 in |
| ISO bore code | 24 |
| Radial section height (D−d)/2 | 70 mm |
| Smallest bore in NUP2300-series | 20 mm |
| Largest outer diameter in NUP2300-series | 300 mm |
| Width range across NUP2300-series | 21–102 mm |
| Bore position in NUP2300-series (smallest first) | 19 of 21 |
| Bore above smallest NUP2300-series size | 100 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ2324-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×260×86 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU2324-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×260×86 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NUP2324-ECML model number is decoded
Ordering number SKF NUP 2324 ECML resolves to a 120×260×86 mm single-row caged cylindrical roller bearing (dimension series 23 (medium-section, wide)); two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring. The NUP configuration means two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring; functionally the bearing is a locating bearing that positions the shaft axially in both directions while keeping the cylindrical-roller radial capacity. The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. The radial section height is 70.0 mm and the catalogue mass 23500 g; at 915 kN dynamic rating this is roughly 7.63 kN of C per millimetre of bore before application factors. Assembly note: the loose inner-ring flange must be fitted on the correct side and retained by the shaft abutment; never omit it during reassembly or the bearing loses its two-direction locating function. Heat steel rings inductively to max 120 °C.
Typical equipment & failure modes
Common applications
- marine propulsion line shafts
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
- offshore drawworks shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- roller-end scoring from inadequate oil flow in the roller-raceway contact
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- smearing (microwelding) on roller surfaces during skid starts with insufficient minimum load
Selection pitfalls — read before you substitute
- Do not use a NUP bearing where a floating non-locating bearing is required — the loose inner flange makes it a locating bearing
- The dimension series 23 (medium-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2324, but flange configuration and axial-locating behaviour differ — quote the full SKF NUP 2324 ECML and do not substitute rib styles without checking the shaft locating scheme.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 260 mm raceway.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 915/1040 kN ratings are SKF catalogue 17000 (2018) values for the ECML execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUP2324-ECML?
SKF NUP 2324 ECML is a single-row caged cylindrical roller bearing with 120 mm bore, 260 mm OD and 86 mm width per ISO 15. SKF lists C 915 kN, C0 1040 kN, Pu 116 kN, reference speed 2,800 r/min and limiting speed 5,000 r/min, mass about 23500 g.
What does the NUP designation and ECML suffix mean?
The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring.
Can NUP2324-ECML take axial load and locate the shaft?
Yes, in both directions: the integral inner flange plus the loose flange ring close both axial paths. Do not pair it with another locating bearing without thermal clearance.
How does NUP2324-ECML compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.