NUP328-ECM bearing: complete specifications & equivalents
The NUP328-ECM is a ISO 15 radial bearing sized 140 x 300 x 62 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 140 mm |
| Outer diameter D | 300 mm |
| Width B | 62 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 780 kN |
| Basic static load rating C0 | 830 kN |
| Fatigue load limit Pu | 88 kN |
| Reference speed (thermal) | 2400 rpm |
| Limiting speed (mechanical) | 2800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 23500 g |
| Manufacturer designation | SKF NUP 328 ECM |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUP300-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 2.441 in |
| ISO bore code | 28 |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in NUP300-series | 20 mm |
| Largest outer diameter in NUP300-series | 300 mm |
| Width range across NUP300-series | 15–62 mm |
| Bore position in NUP300-series (smallest first) | 21 of 21 |
| Bore above smallest NUP300-series size | 120 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ328-ECJ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 140×300×62 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU328-ECM | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 140×300×62 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NUP328-ECM model number is decoded
In SKF catalogue PUB BU/P1 17000, SKF NUP 328 ECM denotes a single-row caged cylindrical roller bearing on the ISO 15 140×300×62 mm envelope, dimension series 3 (medium-section ISO 15 envelope), with catalogue mass 23500 g. Reading the NUP prefix: two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring. This makes the execution a locating bearing that positions the shaft axially in both directions while keeping the cylindrical-roller radial capacity. Reading the order-string suffix ECM: the E-design ECM execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. Selection arithmetic: C0/C ≈ 1.06 (830 against 780 kN), and the Pu figure 88 kN is the fatigue load-limit floor for the SKF life equation; the catalogue lists 2,400 r/min thermal reference speed and 2,800 r/min mechanical limiting speed. Mounting: the loose inner-ring flange must be fitted on the correct side and retained by the shaft abutment; never omit it during reassembly or the bearing loses its two-direction locating function. A 140 mm seat normally takes a m6 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- large rolling-mill drive trains
- marine propulsion line shafts
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- Do not use a NUP bearing where a floating non-locating bearing is required — the loose inner flange makes it a locating bearing
- The dimension series 3 (medium-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 328, but flange configuration and axial-locating behaviour differ — quote the full SKF NUP 328 ECM and do not substitute rib styles without checking the shaft locating scheme.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 62 mm-wide ring and concentrates load.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 780/830 kN ratings are SKF catalogue 17000 (2018) values for the ECM execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUP328-ECM?
SKF NUP 328 ECM is a single-row caged cylindrical roller bearing with 140 mm bore, 300 mm OD and 62 mm width per ISO 15. SKF lists C 780 kN, C0 830 kN, Pu 88 kN, reference speed 2,400 r/min and limiting speed 2,800 r/min, mass about 23500 g.
What does the NUP designation and ECM suffix mean?
The ECM suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring.
Can NUP328-ECM take axial load and locate the shaft?
Yes, in both directions: the integral inner flange plus the loose flange ring close both axial paths. Do not pair it with another locating bearing without thermal clearance.
How does NUP328-ECM compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.