AXK6085 bearing: complete specifications & equivalents

The AXK6085 is a ISO 3031 radial bearing sized 60 x 85 x 3 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 85 mm d = 60 B = 3 mm side section front view
Principal dimensions: bore d 60 mm, outer diameter D 85 mm, width B 3 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 60 mm
Outer diameter D 85 mm
Width B 3 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel
Basic dynamic load rating C 37.5 kN
Basic static load rating C0 232 kN
Fatigue load limit Pu 28.5 kN
Reference speed (thermal) 2200 rpm
Limiting speed (mechanical) 4300 rpm
Operating temperature -40 to +120 °C
Mass 33 g
Manufacturer designation AXK 6085
Standard ISO 3031
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & AXK-series range

Bore d2.362 in
Outer diameter D3.346 in
Width B0.118 in
ISO bore code85
Radial section height (D−d)/212.5 mm
Smallest bore in AXK-series4 mm
Largest outer diameter in AXK-series200 mm
Width range across AXK-series2–5 mm
Bore position in AXK-series (smallest first)17 of 30
Bore above smallest AXK-series size56 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
AXK6085 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the AXK6085 model number is decoded

For transmission gears that would otherwise rub on a housing wall, AXK 6085 supplies a complete needle thrust track between 65 and 83 mm raceway diameters in a 3 mm envelope. Reading the code: AXK marks the needle thrust assembly and the figures 60/85 give the two raceway diameters in millimetres — 60 mm inner track and 85 mm outer track; TN swaps the stamped steel cage for PA66. At this size the stamped steel cage guides long thrust needles; the TN polymer-cage variant is offered where noise matters. One-direction thrust only. The 33 g mass and 3 mm axial height sit between 60 and 85 mm washer diameters; check the seat shoulder spans the full ring face — a narrow shoulder causes washer fretting long before fatigue does. Mounting: harden and grind both mating faces to 58–64 HRC over the full Ea 65–Eb 83 mm band (or fit AS/LS washers), drop the 3 mm cage in flat, and never press or hammer the needle complement.

Typical equipment & failure modes

Common applications

  • light turntables, index plates and office-machine pivots
  • two-wheeler gearbox selector and layshaft thrust faces
  • compact drives where hardened washers replace a machined raceway shoulder
  • automotive manual and automatic transmission thrust positions

Known failure patterns

  • needle-row denting from a single hard particle trapped in the 2 mm section
  • cage wear from rollers being dragged through unloaded zones under fluctuating thrust
  • grease churning and overheating when a high-speed thrust position is over-packed
  • rolling-contact fatigue spalling after the catalogue L10 life is exhausted
  • instant raceway scoring when the assembly runs against a face below 58 HRC or with a rough finish

Selection pitfalls — read before you substitute

  • On a 60 mm shaft the cage is only 3 mm thick — a shaft shoulder with a sharp edge or a 0.1 mm burr will catch and spin the cage instead of locating it.
  • Match washers by the exact 60–85 mm track — a washer sized to the shaft alone leaves the needles overrunning its edge, which shears the cage.
  • the 2,200 r/min reference speed is the thermal criterion under load, the 4,300 r/min limiting speed assumes hardened, ground, oiled faces; soft or dry faces drop the real ceiling drastically.
  • TN polymer and stamped steel cages of the same code (AXK 6085) share envelopes and ratings; the choice is temperature and noise, not load.
  • The AXK code supplies no washers: AXK 6085 arrives as the needle cage only, and a "bearing failure" on hard-faced tracks is usually a missing-AS-washer failure at ordering time.
  • The 37.5/232 kN ratings and 33 g mass are SKF catalogue values transcribed from ch. 12.1 of PUB BU/P1 17000 (PDF table page 908); mounting data — Ea/Eb raceway diameters and the minimum load factor A — appears in the running text because the structured record carries the boundary envelope only.

Frequently asked questions

Why does an AXK assembly fail early?

Almost always the track: missing/undersized washers, hardness below 58 HRC, a sharp shoulder edge catching the cage, or contamination in the thin section. Rating 37.5 kN assumes all of these are correct.

Which dimensions does the AXK 6085 have?

A AXK 6085 measures 60 mm bore × 85 mm outside diameter × 3 mm width (2.362 × 3.346 × 0.118 in). From SKF catalogue PUB BU/P1 17000: dynamic C 37.5 kN, static C0 232 kN, fatigue limit Pu 28.5 kN, reference speed 2,200 r/min, limiting speed 4,300 r/min, mass about 33 g. The contact band runs Ea 65–Eb 83 mm; hardened washers or 58–64 HRC faces are required.

What does AXK 60/85 mean?

A needle roller and cage thrust assembly (ISO 3031) for a 60 mm inner track and 85 mm outer track, 3 mm thick; one-direction axial load, washers ordered separately.

What is the difference between AXK and AXW?

AXW pairs the AXK needle set with a washer carrying an integral centring spigot that locates in a housing register, keeping cage and washer concentric as one part; AXK is the bare cage-and-needle set needing two separate washers. The AXW still needs a separate LS/AS washer or hardened face on the opposite side.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies on 2026-09-27. Read our editorial & correction policy.