AXK7095 bearing: complete specifications & equivalents

The AXK7095 is a ISO 3031 radial bearing sized 70 x 95 x 4 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 95 mm d = 70 B = 4 mm side section front view
Principal dimensions: bore d 70 mm, outer diameter D 95 mm, width B 4 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 70 mm
Outer diameter D 95 mm
Width B 4 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel
Basic dynamic load rating C 49 kN
Basic static load rating C0 255 kN
Fatigue load limit Pu 31 kN
Reference speed (thermal) 1800 rpm
Limiting speed (mechanical) 3600 rpm
Operating temperature -40 to +120 °C
Mass 60 g
Manufacturer designation AXK 7095
Standard ISO 3031
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & AXK-series range

Bore d2.756 in
Outer diameter D3.74 in
Width B0.157 in
ISO bore code95
Radial section height (D−d)/212.5 mm
Smallest bore in AXK-series4 mm
Largest outer diameter in AXK-series200 mm
Width range across AXK-series2–5 mm
Bore position in AXK-series (smallest first)19 of 30
Bore above smallest AXK-series size66 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
AXK7095 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the AXK7095 model number is decoded

The AXK assembly AXK 7095 covers 70–95 mm in a 4 mm section and is rated 49 kN dynamic / 255 kN static: the thinnest rolling thrust support available for that seat. SKF prints the AXK sizes as adjacent figures, so 70/95 reads 70 then 95 mm; the assembly has no washers of its own — order AS/LS washers or harden the mating faces. The thin section tolerates no misalignment: keep the mating faces parallel, and use the AXW spigot-flanged execution where a one-piece, housing-centred cage-plus-washer unit simplifies assembly. No factor A is published for needle thrust sets: keep a light preload so the needles roll rather than skid — springs, shim preload or the gear's own backlash take-up are part of the selection, not an accessory. Mounting: harden and grind both mating faces to 58–64 HRC over the full Ea 74–Eb 93 mm band (or fit AS/LS washers), drop the 4 mm cage in flat, and never press or hammer the needle complement.

Typical equipment & failure modes

Common applications

  • small gearbox gears that need a 2 mm thrust shim between a shaft and face
  • light turntables, index plates and office-machine pivots
  • two-wheeler gearbox selector and layshaft thrust faces
  • compact drives where hardened washers replace a machined raceway shoulder

Known failure patterns

  • instant raceway scoring when the assembly runs against a face below 58 HRC or with a rough finish
  • cage wear from rollers being dragged through unloaded zones under fluctuating thrust
  • grease churning and overheating when a high-speed thrust position is over-packed
  • hard-particle indentation where oil or grease filtration is inadequate
  • edge loading across the needle crowns when the mating faces are not square to the shaft

Selection pitfalls — read before you substitute

  • At 70 mm track diameter, face hardness decides everything: a ground-but-soft washer looks correct yet ribbons within months; specify 58–64 HRC on the drawing.
  • The 49 kN rating is real only at 58–64 HRC face hardness; visual inspection cannot tell a 45 HRC washer from a 60 HRC one — order certified washers.
  • Do not expect misalignment tolerance: a 4 mm rigid needle set edge-loads if the faces tilt even a fraction of a degree — use a spherical or AXW solution where the seat cannot be kept parallel.
  • the 1,800 r/min reference speed is the thermal criterion under load, the 3,600 r/min limiting speed assumes hardened, ground, oiled faces; soft or dry faces drop the real ceiling drastically.
  • The AXK code supplies no washers: AXK 7095 arrives as the needle cage only, and a "bearing failure" on hard-faced tracks is usually a missing-AS-washer failure at ordering time.
  • The 49/255 kN ratings and 60 g mass are SKF catalogue values transcribed from ch. 12.1 of PUB BU/P1 17000 (PDF table page 908); mounting data — Ea/Eb raceway diameters and the minimum load factor A — appears in the running text because the structured record carries the boundary envelope only.

Frequently asked questions

What does AXK 70/95 mean?

A needle roller and cage thrust assembly (ISO 3031) for a 70 mm inner track and 95 mm outer track, 4 mm thick; one-direction axial load, washers ordered separately.

What is the difference between AXK and AXW?

AXW pairs the AXK needle set with a washer carrying an integral centring spigot that locates in a housing register, keeping cage and washer concentric as one part; AXK is the bare cage-and-needle set needing two separate washers. The AXW still needs a separate LS/AS washer or hardened face on the opposite side.

Does the AXK 7095 tolerate misalignment?

No — the 4 mm rigid needle set edge-loads on tilted faces. Keep the shaft and housing faces parallel, or choose the self-aligning roller thrust families.

Why does an AXK assembly fail early?

Almost always the track: missing/undersized washers, hardness below 58 HRC, a sharp shoulder edge catching the cage, or contamination in the thin section. Rating 49 kN assumes all of these are correct.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies on 2026-09-27. Read our editorial & correction policy.