AXK85110 bearing: complete specifications & equivalents

The AXK85110 is a ISO 3031 radial bearing sized 85 x 110 x 4 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 110 mm d = 85 B = 4 mm side section front view
Principal dimensions: bore d 85 mm, outer diameter D 110 mm, width B 4 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 85 mm
Outer diameter D 110 mm
Width B 4 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel
Basic dynamic load rating C 52 kN
Basic static load rating C0 290 kN
Fatigue load limit Pu 35.5 kN
Reference speed (thermal) 1700 rpm
Limiting speed (mechanical) 3400 rpm
Operating temperature -40 to +120 °C
Mass 67 g
Manufacturer designation AXK 85110
Standard ISO 3031
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & AXK-series range

Bore d3.346 in
Outer diameter D4.331 in
Width B0.157 in
ISO bore code10
Radial section height (D−d)/212.5 mm
Smallest bore in AXK-series4 mm
Largest outer diameter in AXK-series200 mm
Width range across AXK-series2–5 mm
Bore position in AXK-series (smallest first)22 of 30
Bore above smallest AXK-series size81 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
AXK85110 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the AXK85110 model number is decoded

For transmission gears that would otherwise rub on a housing wall, AXK 85110 supplies a complete needle thrust track between 89 and 108 mm raceway diameters in a 4 mm envelope. Reading the code: AXK marks the needle thrust assembly and the figures 85/110 give the two raceway diameters in millimetres — 85 mm inner track and 110 mm outer track; TN swaps the stamped steel cage for PA66. At this size the stamped steel cage guides long thrust needles; the TN polymer-cage variant is offered where noise matters. One-direction thrust only. One direction only: AXK 85110 cannot be reversed to take opposite thrust — mirror a second bearing for reversing shafts, and keep housing and shaft seats square within the ISO 104 tolerances. Mounting: harden and grind both mating faces to 58–64 HRC over the full Ea 89–Eb 108 mm band (or fit AS/LS washers), drop the 4 mm cage in flat, and never press or hammer the needle complement.

Typical equipment & failure modes

Common applications

  • compact drives where hardened washers replace a machined raceway shoulder
  • automotive manual and automatic transmission thrust positions
  • torque converter and clutch release assemblies in passenger cars
  • small gearbox gears that need a 2 mm thrust shim between a shaft and face

Known failure patterns

  • instant raceway scoring when the assembly runs against a face below 58 HRC or with a rough finish
  • cage wear from rollers being dragged through unloaded zones under fluctuating thrust
  • grease churning and overheating when a high-speed thrust position is over-packed
  • rolling-contact fatigue spalling after the catalogue L10 life is exhausted
  • edge loading across the needle crowns when the mating faces are not square to the shaft

Selection pitfalls — read before you substitute

  • At 85 mm track diameter, face hardness decides everything: a ground-but-soft washer looks correct yet ribbons within months; specify 58–64 HRC on the drawing.
  • The 52 kN rating is real only at 58–64 HRC face hardness; visual inspection cannot tell a 45 HRC washer from a 60 HRC one — order certified washers.
  • Do not expect misalignment tolerance: a 4 mm rigid needle set edge-loads if the faces tilt even a fraction of a degree — use a spherical or AXW solution where the seat cannot be kept parallel.
  • TN polymer and stamped steel cages of the same code (AXK 85110) share envelopes and ratings; the choice is temperature and noise, not load.
  • The AXK code supplies no washers: AXK 85110 arrives as the needle cage only, and a "bearing failure" on hard-faced tracks is usually a missing-AS-washer failure at ordering time.
  • The 52/290 kN ratings and 67 g mass are SKF catalogue values transcribed from ch. 12.1 of PUB BU/P1 17000 (PDF table page 908); mounting data — Ea/Eb raceway diameters and the minimum load factor A — appears in the running text because the structured record carries the boundary envelope only.

Frequently asked questions

Which dimensions does the AXK 85110 have?

A AXK 85110 measures 85 mm bore × 110 mm outside diameter × 4 mm width (3.346 × 4.331 × 0.157 in). From SKF catalogue PUB BU/P1 17000: dynamic C 52 kN, static C0 290 kN, fatigue limit Pu 35.5 kN, reference speed 1,700 r/min, limiting speed 3,400 r/min, mass about 67 g. The contact band runs Ea 89–Eb 108 mm; hardened washers or 58–64 HRC faces are required.

What does AXK 85/110 mean?

A needle roller and cage thrust assembly (ISO 3031) for a 85 mm inner track and 110 mm outer track, 4 mm thick; one-direction axial load, washers ordered separately.

What is the difference between AXK and AXW?

AXW pairs the AXK needle set with a washer carrying an integral centring spigot that locates in a housing register, keeping cage and washer concentric as one part; AXK is the bare cage-and-needle set needing two separate washers. The AXW still needs a separate LS/AS washer or hardened face on the opposite side.

Does the AXK 85110 tolerate misalignment?

No — the 4 mm rigid needle set edge-loads on tilted faces. Keep the shaft and housing faces parallel, or choose the self-aligning roller thrust families.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies on 2026-09-27. Read our editorial & correction policy.