HK1616 bearing: complete specifications & equivalents
The HK1616 is a ISO 3245 radial bearing sized 16 x 22 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 16 mm |
| Outer diameter D | 22 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 10.5 kN |
| Basic static load rating C0 | 15.6 kN |
| Fatigue load limit Pu | 1.8 kN |
| Reference speed (thermal) | 14000 rpm |
| Limiting speed (mechanical) | 16000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 16 g |
| Manufacturer designation | HK 1616 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.63 in |
|---|---|
| Outer diameter D | 0.866 in |
| Width B | 0.63 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 13 of 26 |
| Bore above smallest HK-series size | 13 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK1616F | NTN | full Dimensions and internal design equivalent — standard interchange. | NTN counterpart on the same 16×22×16 mm envelope with ratings within 10 % — interchange after checking the execution (cage/seal) details on both pages. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK1616 model number is decoded
HK 1616 is the standard caged drawn cup execution for a 16 mm shaft: ISO 3245 boundary dimensions (16×22×16 mm), open at both ends so the shaft can be pushed through, and rated 10.5 kN dynamic. The designation HK 1616 encodes geometry only — there is no bore code to decode, since the 16 mm Fw is printed directly in the first digits and the cup width 16 mm in the last two. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. The suffix TN denotes the glass fibre reinforced PA66 cage; the 2RS execution adds rubber contact seals on both faces, retaining factory grease for life-lubricated pivots. Selection arithmetic: C 10.5 kN against C0 15.6 kN gives a C0/C ratio of 1.49, and the 1.8 kN fatigue load limit Pu sets the floor for the adjusted-life calculation at contaminated lubrication. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
- spindle clusters of drilling and tapping units
- auto steering gear rack supports
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- brinelling of raceways from impact or pressing force transmitted through the rolling elements
Selection pitfalls — read before you substitute
- On a 16 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 22 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Reference and limiting speeds are different limits: the 14,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 16 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The 10.5/15.6 kN ratings and 16 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 620); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What mounting mistakes ruin a HK 1616?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 1616 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Which dimensions does the HK 1616 have?
A HK 1616 measures 16 mm bore/Fw × 22 mm outside diameter × 16 mm width (0.63 × 0.866 × 0.63 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 10.5 kN, static C0 15.6 kN, fatigue limit Pu 1.8 kN, limiting speed 16,000 r/min, reference speed 14,000 r/min, mass about 16 g.
What does HK 1616 mean in SKF part numbering?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 16 mm, the last two the width 16 mm, the shell OD 22 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.