HK1712 bearing: complete specifications & equivalents
The HK1712 is a ISO 3245 radial bearing sized 17 x 23 x 12 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 17 mm |
| Outer diameter D | 23 mm |
| Width B | 12 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 7.65 kN |
| Basic static load rating C0 | 10.6 kN |
| Fatigue load limit Pu | 1.2 kN |
| Reference speed (thermal) | 14000 rpm |
| Limiting speed (mechanical) | 15000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 13 g |
| Manufacturer designation | HK 1712 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.669 in |
|---|---|
| Outer diameter D | 0.906 in |
| Width B | 0.472 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 14 of 26 |
| Bore above smallest HK-series size | 14 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK1712 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK1712 model number is decoded
HK 1712 is the standard caged drawn cup execution for a 17 mm shaft: ISO 3245 boundary dimensions (17×23×12 mm), open at both ends so the shaft can be pushed through, and rated 7.65 kN dynamic. Reading the code: HK marks the open-end drawn cup series, the first two digits (17) give the 17 mm under-roller diameter Fw, the last two (12) the 12 mm width; the 23 mm OD follows the ISO 3245 plan. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Caged HK bearings space the rollers for lower friction than full complement HK types; the cage is not a seal — 2RS executions are the sealed members of the family. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- brinelling of raceways from impact or pressing force transmitted through the rolling elements
Selection pitfalls — read before you substitute
- On a 17 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 23 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- The quoted 7.65/10.6 kN ratings are SKF catalogue values for this exact execution (HK 1712); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 7.65/10.6 kN ratings and 13 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 620); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Does the HK 1712 need a hardened and ground shaft?
No. In this execution the 17 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 1712?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 1712 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Which dimensions does the HK 1712 have?
A HK 1712 measures 17 mm bore/Fw × 23 mm outside diameter × 12 mm width (0.669 × 0.906 × 0.472 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 7.65 kN, static C0 10.6 kN, fatigue limit Pu 1.2 kN, limiting speed 15,000 r/min, reference speed 14,000 r/min, mass about 13 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.