HK2512 bearing: complete specifications & equivalents
The HK2512 is a ISO 3245 radial bearing sized 25 x 32 x 12 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 25 mm |
| Outer diameter D | 32 mm |
| Width B | 12 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 10.5 kN |
| Basic static load rating C0 | 15.3 kN |
| Fatigue load limit Pu | 1.76 kN |
| Reference speed (thermal) | 9500 rpm |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 20 g |
| Manufacturer designation | HK 2512 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.984 in |
|---|---|
| Outer diameter D | 1.26 in |
| Width B | 0.472 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 3.5 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 18 of 26 |
| Bore above smallest HK-series size | 22 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK2512 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK2512 model number is decoded
In SKF catalogue PUB BU/P1 17000, HK 2512 denotes a 25×32×12 mm drawn cup needle roller bearing with open ends — the shaft journal is the inner raceway, the pressed shell the outer, and the cage keeps the rollers parallel. The designation HK 2512 encodes geometry only — there is no bore code to decode, since the 25 mm Fw is printed directly in the first digits and the cup width 12 mm in the last two. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. The shell itself is the outer ring: hardened sheet steel, closed at neither end (open type), so the shaft can pass through and lubricant can be fed axially along the journal. Catalogue mass 20 g at 25×32×12 mm makes this one of the highest capacity-per-gram choices in the drawn cup needle roller bearings, open end; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
- spindle clusters of drilling and tapping units
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- drawn-cup shell distortion or splitting from a careless press-in without a seating mandrel
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- false brinelling of standby equipment under external vibration
Selection pitfalls — read before you substitute
- On a 25 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 32 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Reference and limiting speeds are different limits: the 9,500 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 25 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The 10.5/15.3 kN ratings and 20 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does HK 2512 mean in SKF part numbering?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 25 mm, the last two the width 12 mm, the shell OD 32 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Does the HK 2512 need a hardened and ground shaft?
No. In this execution the 25 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 2512?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 2512 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.