HK2526 bearing: complete specifications & equivalents
The HK2526 is a ISO 3245 radial bearing sized 25 x 32 x 26 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 25 mm |
| Outer diameter D | 32 mm |
| Width B | 26 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 24.2 kN |
| Basic static load rating C0 | 45 kN |
| Fatigue load limit Pu | 5.5 kN |
| Reference speed (thermal) | 9500 rpm |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 44 g |
| Manufacturer designation | HK 2526 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.984 in |
|---|---|
| Outer diameter D | 1.26 in |
| Width B | 1.024 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 3.5 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 18 of 26 |
| Bore above smallest HK-series size | 22 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK2526 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK2526 model number is decoded
Ordering number HK 2526 in SKF catalogue PUB BU/P1 17000 is an open-end HK drawn cup needle roller bearing: nominal code 25 for the 25 mm under-roller diameter and 26 for the 26 mm width. SKF's HK numbering puts the shaft size first: 25 → Fw 25 mm (the ground, hardened journal), 26 → width 26 mm, with the 32 mm shell OD from the ISO 3245 dimension table. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. The shell itself is the outer ring: hardened sheet steel, closed at neither end (open type), so the shaft can pass through and lubricant can be fed axially along the journal. Catalogue mass 44 g at 25×32×26 mm makes this one of the highest capacity-per-gram choices in the drawn cup needle roller bearings, open end; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Mounting: press the cup in with a shouldered mandrel against the stamped end face only — through-the-rollers pressing brinells both raceways; the housing bore takes a firm press fit and the shaft slides in after.
Typical equipment & failure modes
Common applications
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
- spindle clusters of drilling and tapping units
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- corrosion pitting from condensation in intermittently operated machinery
Selection pitfalls — read before you substitute
- On a 25 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 32 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- The 24.2/45 kN ratings and 44 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What limits the service life of a HK 2526?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 25 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 3.5 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the HK 2526?
A HK 2526 measures 25 mm bore/Fw × 32 mm outside diameter × 26 mm width (0.984 × 1.26 × 1.024 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 24.2 kN, static C0 45 kN, fatigue limit Pu 5.5 kN, limiting speed 11,000 r/min, reference speed 9,500 r/min, mass about 44 g.
How is the HK 2526 designation read?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 25 mm, the last two the width 26 mm, the shell OD 32 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Can the HK 2526 run on an unhardened shaft?
No. In this execution the 25 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.