HK3016 bearing: complete specifications & equivalents
The HK3016 is a ISO 3245 radial bearing sized 30 x 37 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 30 mm |
| Outer diameter D | 37 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 16.5 kN |
| Basic static load rating C0 | 29 kN |
| Fatigue load limit Pu | 3.4 kN |
| Reference speed (thermal) | 8000 rpm |
| Limiting speed (mechanical) | 9000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 31 g |
| Manufacturer designation | HK 3016 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 1.457 in |
| Width B | 0.63 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 3.5 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 20 of 26 |
| Bore above smallest HK-series size | 27 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK3016-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 30×37×16 mm envelope, but catalogue C/C0 differ between the executions (16.5/29 vs 11.7/18.3 kN) — boundary dimensions match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK3016 model number is decoded
HK 3016 is an open-end drawn cup needle roller bearing to ISO 3245: a hardened, thin-walled shell of 37 mm outside diameter carrying a caged needle roller set for a 30 mm shaft, listed by SKF in SKF catalogue PUB BU/P1 17000. Reading the code: HK marks the open-end drawn cup series, the first two digits (30) give the 30 mm under-roller diameter Fw, the last two (16) the 16 mm width; the 37 mm OD follows the ISO 3245 plan. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Caged HK bearings space the rollers for lower friction than full complement HK types; the cage is not a seal — 2RS executions are the sealed members of the family. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. Open ends mean the housing must do the sealing; where that is impossible, the 2RS execution with its integrated seals and grease fill replaces sealing rings that would not fit the 16 mm section.
Typical equipment & failure modes
Common applications
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- hard-particle indentation in unfiltered lubricant
Selection pitfalls — read before you substitute
- At 30 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 30 mm seats can bend past the compensation range long before the load rating is exhausted.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- Do not interchange envelope-identical needle families blindly: HK 3016 shares its 30×37×16 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- The 16.5/29 kN ratings and 31 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does HK 3016 mean in SKF part numbering?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 30 mm, the last two the width 16 mm, the shell OD 37 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Does the HK 3016 need a hardened and ground shaft?
No. In this execution the 30 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 3016?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 3016 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.