HK3026 bearing: complete specifications & equivalents
The HK3026 is a ISO 3245 radial bearing sized 30 x 37 x 26 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 30 mm |
| Outer diameter D | 37 mm |
| Width B | 26 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 27 kN |
| Basic static load rating C0 | 54 kN |
| Fatigue load limit Pu | 6.55 kN |
| Reference speed (thermal) | 8000 rpm |
| Limiting speed (mechanical) | 9000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 51 g |
| Manufacturer designation | HK 3026 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 1.457 in |
| Width B | 1.024 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 3.5 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 20 of 26 |
| Bore above smallest HK-series size | 27 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK3026 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK3026 model number is decoded
HK 3026 is the standard caged drawn cup execution for a 30 mm shaft: ISO 3245 boundary dimensions (30×37×26 mm), open at both ends so the shaft can be pushed through, and rated 27 kN dynamic. In HK 3026, Fw = 30 mm names the shaft that becomes the inner raceway and B = 26 mm the cup width; the shell outside diameter 37 mm is fixed by the boundary plan, so the housing bore needs only a press-fit tolerance. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Caged HK bearings space the rollers for lower friction than full complement HK types; the cage is not a seal — 2RS executions are the sealed members of the family. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- drawn-cup shell distortion or splitting from a careless press-in without a seating mandrel
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- false brinelling of standby equipment under external vibration
Selection pitfalls — read before you substitute
- At 30 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 30 mm seats can bend past the compensation range long before the load rating is exhausted.
- Do not interchange envelope-identical needle families blindly: HK 3026 shares its 30×37×26 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- Reference and limiting speeds are different limits: the 8,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- The 27/54 kN ratings and 51 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
How should the HK 3026 be mounted?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
What limits the service life of a HK 3026?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 30 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 3.5 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the HK 3026?
A HK 3026 measures 30 mm bore/Fw × 37 mm outside diameter × 26 mm width (1.181 × 1.457 × 1.024 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 27 kN, static C0 54 kN, fatigue limit Pu 6.55 kN, limiting speed 9,000 r/min, reference speed 8,000 r/min, mass about 51 g.
How is the HK 3026 designation read?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 30 mm, the last two the width 26 mm, the shell OD 37 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.