HK5528 bearing: complete specifications & equivalents
The HK5528 is a ISO 3245 radial bearing sized 55 x 63 x 28 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 55 mm |
| Outer diameter D | 63 mm |
| Width B | 28 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 41.8 kN |
| Basic static load rating C0 | 104 kN |
| Fatigue load limit Pu | 12.9 kN |
| Reference speed (thermal) | 4500 rpm |
| Limiting speed (mechanical) | 5000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 105 g |
| Manufacturer designation | HK 5528 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 2.165 in |
|---|---|
| Outer diameter D | 2.48 in |
| Width B | 1.102 in |
| ISO bore code | 28 |
| Radial section height (D−d)/2 | 4 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 25 of 26 |
| Bore above smallest HK-series size | 52 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK5528 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK5528 model number is decoded
Ordering number HK 5528 in SKF catalogue PUB BU/P1 17000 is an open-end HK drawn cup needle roller bearing: nominal code 55 for the 55 mm under-roller diameter and 28 for the 28 mm width. The designation HK 5528 encodes geometry only — there is no bore code to decode, since the 55 mm Fw is printed directly in the first digits and the cup width 28 mm in the last two. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. The shell itself is the outer ring: hardened sheet steel, closed at neither end (open type), so the shaft can pass through and lubricant can be fed axially along the journal. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. Open ends mean the housing must do the sealing; where that is impossible, the 2RS execution with its integrated seals and grease fill replaces sealing rings that would not fit the 28 mm section.
Typical equipment & failure modes
Common applications
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- hard-particle indentation in unfiltered lubricant
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 55 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Reference and limiting speeds are different limits: the 4,500 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 55 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The 41.8/104 kN ratings and 105 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 624); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Does the HK 5528 need a hardened and ground shaft?
No. In this execution the 55 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 5528?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 5528 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Which dimensions does the HK 5528 have?
A HK 5528 measures 55 mm bore/Fw × 63 mm outside diameter × 28 mm width (2.165 × 2.48 × 1.102 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 41.8 kN, static C0 104 kN, fatigue limit Pu 12.9 kN, limiting speed 5,000 r/min, reference speed 4,500 r/min, mass about 105 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.