NA4826 bearing: complete specifications & equivalents
The NA4826 is a ISO 1206 radial bearing sized 130 x 165 x 35 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 130 mm |
| Outer diameter D | 165 mm |
| Width B | 35 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 119 kN |
| Basic static load rating C0 | 325 kN |
| Fatigue load limit Pu | 36.5 kN |
| Reference speed (thermal) | 2800 rpm |
| Limiting speed (mechanical) | 3200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1800 g |
| Manufacturer designation | NA 4826 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NA-48-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 6.496 in |
| Width B | 1.378 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 17.5 mm |
| Smallest bore in NA-48-series | 110 mm |
| Largest outer diameter in NA-48-series | 480 mm |
| Width range across NA-48-series | 30–100 mm |
| Bore position in NA-48-series (smallest first) | 3 of 19 |
| Bore above smallest NA-48-series size | 20 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NA4826 model number is decoded
In SKF catalogue PUB BU/P1 17000, NA 4826 denotes a complete needle roller bearing for a 130 mm shaft — machined inner and outer rings, integral flanges on the outer ring retaining the roller set, 165 mm OD and 35 mm width. The designation NA 4826 tells you the envelope — 130×165×35 mm — and the family tells you the construction: complete bearing, replaceable inner ring, flanged outer ring retaining the needle rollers. Execution notes: the inner ring is ground on bore and raceway, so the shaft seat is a normal k5/j6; the flanged outer ring needs no housing shoulder, and NA 49 2RS executions add seals with a wider outer ring. Selection arithmetic: C 119 kN against C0 325 kN gives a C0/C ratio of 2.73, and the 36.5 kN fatigue load limit Pu sets the floor for the adjusted-life calculation at contaminated lubrication. For NA 49 2RS executions the wider outer ring changes the housing depth: verify the 35 mm width and s offset dimensions against the open execution before reusing an existing bore.
Typical equipment & failure modes
Common applications
- gearbox shafts where the journal cannot be hardened on site
- wheel and lever pivots needing a replaceable inner ring
- conveyor roller ends and return rollers
- agricultural implement pivots and cutter heads
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- cage pocket wear and roller skew after sustained operation with too little radial preload
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- electrical erosion on VFD-driven shafts without brush or insulated mounting
- inner-ring bore fretting on a loose shaft seat, migrating hard particles into the rolling contact
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 130 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Hardness is load capacity: in families without an inner ring the 130 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The quoted 119/325 kN ratings are SKF catalogue values for this exact execution (NA 4826); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- The 119/325 kN ratings and 1800 g mass are SKF catalogue values transcribed from ch. 7.4 of PUB BU/P1 17000 (PDF table page 646); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What limits the service life of a NA 4826?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 130 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 17.5 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the NA 4826?
A NA 4826 measures 130 mm bore/Fw × 165 mm outside diameter × 35 mm width (5.118 × 6.496 × 1.378 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 119 kN, static C0 325 kN, fatigue limit Pu 36.5 kN, limiting speed 3,200 r/min, reference speed 2,800 r/min, mass about 1800 g.
How is the NA 4826 designation read?
The letters mark a machined-ring needle roller bearing with inner ring: 130 mm bore, 35 mm width, 165 mm OD per the series plan. The hardened inner ring is the raceway, so an ordinary k5 shaft seat suffices.
Can the NA 4826 run on an unhardened shaft?
Yes — that is the point of this family. The NA 4826 carries its own hardened, ground inner ring on a 130 mm seat, so the shaft needs only a normal k5/j6 finish. The inner ring is separable and replaceable.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring on 2026-09-26. Read our editorial & correction policy.