NK19-16 bearing: complete specifications & equivalents
The NK19-16 is a DIN 616 radial bearing sized 19 x 27 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 19 mm |
| Outer diameter D | 27 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 13.4 kN |
| Basic static load rating C0 | 19 kN |
| Fatigue load limit Pu | 2.28 kN |
| Reference speed (thermal) | 20000 rpm |
| Limiting speed (mechanical) | 24000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 26 g |
| Manufacturer designation | NK 19/16 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NK-series range
| Bore d | 0.748 in |
|---|---|
| Outer diameter D | 1.063 in |
| Width B | 0.63 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 4 mm |
| Smallest bore in NK-series | 5 mm |
| Largest outer diameter in NK-series | 130 mm |
| Width range across NK-series | 10–40 mm |
| Bore position in NK-series (smallest first) | 13 of 46 |
| Bore above smallest NK-series size | 14 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NK19-16 model number is decoded
NK 19/16 is a ribbed machined-ring needle roller bearing (no inner ring) sized 19×27×16 mm: the ground outside diameter seats in the housing, the integral flanges hold the rollers, and the 19 mm shaft journal completes the bearing. Reading the designation: NK gives the series and the numbers the boundary plan — 19 mm Fw for the shaft seat, 16 mm width; the 27 mm OD comes from the dimension series, and the absence of an inner ring is built into the family name. SKF offers this family open as standard; a matching IR inner ring can be added separately when the shaft cannot be hardened, which converts the envelope into the NKI/NA equivalent. Selection arithmetic: C 13.4 kN against C0 19 kN gives a C0/C ratio of 1.42, and the 2.28 kN fatigue load limit Pu sets the floor for the adjusted-life calculation at contaminated lubrication. Mounting: the flanged outer ring presses into the H7 housing bore against its flange face; the shaft (hardened to 58–64 HRC, ground) enters afterwards, and axial retention is by the housing wall plus a cover washer.
Typical equipment & failure modes
Common applications
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
- guide rollers running on hardened tracks
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- corrosion pitting from condensation in intermittently operated machinery
- smearing of rollers and journal during idle periods because the radial section holds too little lubricant
Selection pitfalls — read before you substitute
- On a 19 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 27 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Reference and limiting speeds are different limits: the 20,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 19 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The 13.4/19 kN ratings and 26 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 626); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does NK 19/16 mean in SKF part numbering?
NK names a machined-ring needle roller bearing without inner ring: the figures give Fw 19 mm and width 16 mm, OD 27 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Does the NK 19/16 need a hardened and ground shaft?
No. In this execution the 19 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a NK 19/16?
Press on the ring faces only with a fitting sleeve, keep everything square to the 19 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Is the NK 19/16 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.