NK21-20 bearing: complete specifications & equivalents
The NK21-20 is a DIN 616 radial bearing sized 21 x 29 x 20 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 21 mm |
| Outer diameter D | 29 mm |
| Width B | 20 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 17.2 kN |
| Basic static load rating C0 | 27 kN |
| Fatigue load limit Pu | 3.35 kN |
| Reference speed (thermal) | 19000 rpm |
| Limiting speed (mechanical) | 22000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 35 g |
| Manufacturer designation | NK 21/20 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NK-series range
| Bore d | 0.827 in |
|---|---|
| Outer diameter D | 1.142 in |
| Width B | 0.787 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 4 mm |
| Smallest bore in NK-series | 5 mm |
| Largest outer diameter in NK-series | 130 mm |
| Width range across NK-series | 10–40 mm |
| Bore position in NK-series (smallest first) | 15 of 46 |
| Bore above smallest NK-series size | 16 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NK21-20 model number is decoded
NK 21/20 is a ribbed machined-ring needle roller bearing (no inner ring) sized 21×29×20 mm: the ground outside diameter seats in the housing, the integral flanges hold the rollers, and the 21 mm shaft journal completes the bearing. The NK 21/20 code states Fw 21 and width 20 mm directly; because the family has no inner ring, the 21 mm journal must be ground, hardened to 58–64 HRC and finished to the raceway tolerance the catalogue specifies. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. Mounting: the flanged outer ring presses into the H7 housing bore against its flange face; the shaft (hardened to 58–64 HRC, ground) enters afterwards, and axial retention is by the housing wall plus a cover washer.
Typical equipment & failure modes
Common applications
- swing arms and lever pivots with oscillating duty
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- cage pocket wear and roller skew after sustained operation with too little radial preload
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- rolling-contact fatigue spalling after the rated L10 life
- smearing of rollers and journal during idle periods because the radial section holds too little lubricant
Selection pitfalls — read before you substitute
- On a 21 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 29 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Hardness is load capacity: in families without an inner ring the 21 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The quoted 17.2/27 kN ratings are SKF catalogue values for this exact execution (NK 21/20); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- The 17.2/27 kN ratings and 35 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 628); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
How is the NK 21/20 designation read?
NK names a machined-ring needle roller bearing without inner ring: the figures give Fw 21 mm and width 20 mm, OD 29 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Can the NK 21/20 run on an unhardened shaft?
No. In this execution the 21 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the NK 21/20 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 21 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a NK 21/20?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 21 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 4.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.