NKI7-16-TN bearing: complete specifications & equivalents
The NKI7-16-TN is a DIN 616 radial bearing sized 7 x 17 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 7 mm |
| Outer diameter D | 17 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 5.94 kN |
| Basic static load rating C0 | 8 kN |
| Fatigue load limit Pu | 0.9 kN |
| Reference speed (thermal) | 28000 rpm |
| Limiting speed (mechanical) | 32000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 18 g |
| Manufacturer designation | NKI 7/16 TN |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NKI-series range
| Bore d | 0.276 in |
|---|---|
| Outer diameter D | 0.669 in |
| Width B | 0.63 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 5 mm |
| Smallest bore in NKI-series | 5 mm |
| Largest outer diameter in NKI-series | 130 mm |
| Width range across NKI-series | 12–40 mm |
| Bore position in NKI-series (smallest first) | 3 of 30 |
| Bore above smallest NKI-series size | 2 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NKI7-16-TN model number is decoded
SKF lists NKI 7/16 TN in the machined-ring needle roller bearings with inner ring with boundary dimensions 7×17×16 mm: an inner ring turns on the shaft while the flanged outer ring carries the needle roller complement in the housing. In SKF nomenclature the leading letters mark a machined-ring needle bearing with inner ring: figures state 7 mm d and 16 mm B, the 17 mm outside diameter from the machined-ring needle roller bearings with inner ring, and the 2RS suffix would add contact seals. Execution notes: the inner ring is ground on bore and raceway, so the shaft seat is a normal k5/j6; the flanged outer ring needs no housing shoulder, and NA 49 2RS executions add seals with a wider outer ring. For life calculation, the 5.94/8 kN ratings assume raceway geometry supplied by the shaft and housing in families without an inner ring — journal hardness, roundness and finish are part of the bearing, not of the application. For NA 49 2RS executions the wider outer ring changes the housing depth: verify the 16 mm width and s offset dimensions against the open execution before reusing an existing bore.
Typical equipment & failure modes
Common applications
- agricultural implement pivots and cutter heads
- electric motor armature shafts with ground seats
- printing and paper-handling rollers
- gearbox shafts where the journal cannot be hardened on site
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- cage pocket wear and roller skew after sustained operation with too little radial preload
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- electrical erosion on VFD-driven shafts without brush or insulated mounting
- inner-ring bore fretting on a loose shaft seat, migrating hard particles into the rolling contact
Selection pitfalls — read before you substitute
- At Fw 7 mm the rolling elements are under two millimetres long — handle the NKI 7/16 TN like a watch part: one dropped assembly, one over-pressed cup or one coarse journal finish outweighs any catalogue rating difference.
- The quoted 5.94/8 kN ratings are SKF catalogue values for this exact execution (NKI 7/16 TN); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 5.94/8 kN ratings and 18 g mass are SKF catalogue values transcribed from ch. 7.4 of PUB BU/P1 17000 (PDF table page 638); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Which dimensions does the NKI 7/16 TN have?
A NKI 7/16 TN measures 7 mm bore/Fw × 17 mm outside diameter × 16 mm width (0.276 × 0.669 × 0.63 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 5.94 kN, static C0 8 kN, fatigue limit Pu 0.9 kN, limiting speed 32,000 r/min, reference speed 28,000 r/min, mass about 18 g.
What does NKI 7/16 TN mean in SKF part numbering?
The letters mark a machined-ring needle roller bearing with inner ring: 7 mm bore, 16 mm width, 17 mm OD per the series plan. The hardened inner ring is the raceway, so an ordinary k5 shaft seat suffices.
Does the NKI 7/16 TN need a hardened and ground shaft?
Yes — that is the point of this family. The NKI 7/16 TN carries its own hardened, ground inner ring on a 7 mm seat, so the shaft needs only a normal k5/j6 finish. The inner ring is separable and replaceable.
What mounting mistakes ruin a NKI 7/16 TN?
Mount the inner ring on the 7 mm seat first (induction heat, max 120 °C, or press), then fit the flanged outer ring into the H7 housing bore. Verify free rotation and, for 2RS executions, check the wider outer ring against the housing depth.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring on 2026-09-26. Read our editorial & correction policy.