NKS45 bearing: complete specifications & equivalents
The NKS45 is a DIN 616 radial bearing sized 45 x 60 x 22 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 45 mm |
| Outer diameter D | 60 mm |
| Width B | 22 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 40.2 kN |
| Basic static load rating C0 | 64 kN |
| Fatigue load limit Pu | 8 kN |
| Reference speed (thermal) | 8500 rpm |
| Limiting speed (mechanical) | 10000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 150 g |
| Manufacturer designation | NKS 45 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NKS-series range
| Bore d | 1.772 in |
|---|---|
| Outer diameter D | 2.362 in |
| Width B | 0.866 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 7.5 mm |
| Smallest bore in NKS-series | 20 mm |
| Largest outer diameter in NKS-series | 95 mm |
| Width range across NKS-series | 20–28 mm |
| Bore position in NKS-series (smallest first) | 11 of 17 |
| Bore above smallest NKS-series size | 25 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NKS45 model number is decoded
In SKF catalogue PUB BU/P1 17000, NKS 45 designates a flanged, machined outer ring filled with needle rollers and a cage for a 45 mm shaft — heavier section and higher accuracy than a drawn cup, with no inner ring so the journal is the raceway. Reading the designation: NKS gives the series and the numbers the boundary plan — 45 mm Fw for the shaft seat, 22 mm width; the 60 mm OD comes from the dimension series, and the absence of an inner ring is built into the family name. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- swing arms and lever pivots with oscillating duty
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- hard-particle indentation in unfiltered lubricant
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- At 45 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 45 mm seats can bend past the compensation range long before the load rating is exhausted.
- The quoted 40.2/64 kN ratings are SKF catalogue values for this exact execution (NKS 45); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 40.2/64 kN ratings and 150 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 632); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does NKS 45 mean in SKF part numbering?
NKS names a machined-ring needle roller bearing without inner ring: the figures give Fw 45 mm and width 22 mm, OD 60 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Does the NKS 45 need a hardened and ground shaft?
No. In this execution the 45 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a NKS 45?
Press on the ring faces only with a fitting sleeve, keep everything square to the 45 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Is the NKS 45 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.