NKX40-Z bearing: complete specifications & equivalents
The NKX40-Z is a DIN 616 radial bearing sized 40 x 52 x 32 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 40 mm |
| Outer diameter D | 52 mm |
| Width B | 32 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 26.4 kN |
| Basic static load rating C0 | 51 kN |
| Fatigue load limit Pu | 6.3 kN |
| Reference speed (thermal) | 5000 rpm |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 210 g |
| Manufacturer designation | NKX 40 Z |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NKX-series range
| Bore d | 1.575 in |
|---|---|
| Outer diameter D | 2.047 in |
| Width B | 1.26 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in NKX-series | 10 mm |
| Largest outer diameter in NKX-series | 85 mm |
| Width range across NKX-series | 23–40 mm |
| Bore position in NKX-series (smallest first) | 9 of 13 |
| Bore above smallest NKX-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NKX40 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 40×52×32 mm envelope and equivalent catalogue ratings; NKX40 is the combined needle/thrust ball execution — boundary-dimension interchangeable, execution differences (seals, shields, cage) apply. |
| NKXR40 | SKF | full Dimensions and internal design equivalent — standard interchange. | Envelope-identical (40×52×32 mm) combined needle/thrust needle execution with ratings within 10 % — substitution possible after checking ring/flange construction. |
| NKXR40-Z | SKF | full Dimensions and internal design equivalent — standard interchange. | Envelope-identical (40×52×32 mm) combined needle/thrust needle execution with ratings within 10 % — substitution possible after checking ring/flange construction. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NKX40-Z model number is decoded
In SKF catalogue PUB BU/P1 17000, NKX 40 Z designates a combined bearing with needle roller radial part and caged thrust ball part: 40 mm shaft seat, 52 mm OD, thrust dynamic rating 27 kN (Ca). The NKX 40 Z figure gives the 40 mm Fw; the letters fix the construction — radial needle cage plus thrust ball set with pressed cages — and the Z or TN suffix only modifies the thrust part. Execution notes: the Z suffix adds a shield over the thrust balls, TN a polymer cage; the open execution allows relubrication through the shaft, the Z execution is greased for life. The minimum load factor A 0.024 applies to the thrust part: below that axial load the rolling elements of the thrust set skid, so springs or preload washers are part of the arrangement, not an afterthought. Apply the working axial load after mounting and re-check running torque; a rising torque in the first minutes signals balls climbing the washer lip under reversed thrust.
Typical equipment & failure modes
Common applications
- turntable and swivel mounts
- machine tool feed spindles with one-direction thrust
- pump impeller shafts with steady axial pull
- gear pairs generating one-direction axial force
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- hard-particle indentation in unfiltered lubricant
- thrust-part ball or roller skidding and smearing when the axial load falls below the minimum factor
Selection pitfalls — read before you substitute
- At 40 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 40 mm seats can bend past the compensation range long before the load rating is exhausted.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- The thrust part is one-direction: reverse axial events — however brief — lift the rolling elements off the raceway, and the subsequent re-entry impact dents the washer face; mount the NKX 40 Z facing the working thrust.
- Minimum axial load is a real requirement: below factor A 0.024 the thrust elements skid, polish their raceways and lose them — springs or preload washers belong in the arrangement drawing, not the troubleshooting notes.
- The 26.4/51 kN ratings and 210 g mass are SKF catalogue values transcribed from ch. 7.9 of PUB BU/P1 17000 (PDF table page 658); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
How should the NKX 40 Z be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 40 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a NKX 40 Z?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 40 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 6.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the NKX 40 Z?
A NKX 40 Z measures 40 mm bore/Fw × 52 mm outside diameter × 32 mm width (1.575 × 2.047 × 1.26 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 26.4 kN, static C0 51 kN, fatigue limit Pu 6.3 kN, limiting speed 4,000 r/min, reference speed 5,000 r/min, mass about 210 g. Axial ratings of the thrust part: dynamic Ca 27 kN (Ca), static C0a 68 kN (C0a), minimum load factor A 0.024; the thrust set carries load in one direction only.
How is the NKX 40 Z designation read?
NKX = needle roller radial part + caged thrust ball part for a 40 mm shaft: 52 mm OD, 32 mm overall height. The caged thrust part trades some axial capacity for higher permissible speed versus NX.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part on 2026-09-26. Read our editorial & correction policy.