NKX60 bearing: complete specifications & equivalents
The NKX60 is a DIN 616 radial bearing sized 60 x 72 x 40 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 60 mm |
| Outer diameter D | 72 mm |
| Width B | 40 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 41.8 kN |
| Basic static load rating C0 | 96.5 kN |
| Fatigue load limit Pu | 11.8 kN |
| Reference speed (thermal) | 3600 rpm |
| Limiting speed (mechanical) | 5000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 360 g |
| Manufacturer designation | NKX 60 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NKX-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 2.835 in |
| Width B | 1.575 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in NKX-series | 10 mm |
| Largest outer diameter in NKX-series | 85 mm |
| Width range across NKX-series | 23–40 mm |
| Bore position in NKX-series (smallest first) | 12 of 13 |
| Bore above smallest NKX-series size | 50 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NKX60-Z | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 60×72×40 mm envelope and equivalent catalogue ratings; NKX60-Z is the combined needle/thrust ball execution — boundary-dimension interchangeable, execution differences (seals, shields, cage) apply. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NKX60 model number is decoded
For a 60 mm shaft under radial plus one-direction axial load, NKX 60 from the combined needle roller / thrust ball bearings with caged thrust part provides both in 72×40 mm: needle roller cage below, caged thrust ball set above. The code NKX 60 reads as combined radial/thrust for a 60 mm shaft; the catalogue height 40 mm stacks the radial cage and the thrust set, and the 72 mm OD seats both parts in one bore. Execution notes: the Z suffix adds a shield over the thrust balls, TN a polymer cage; the open execution allows relubrication through the shaft, the Z execution is greased for life. The minimum load factor A 0.077 applies to the thrust part: below that axial load the rolling elements of the thrust set skid, so springs or preload washers are part of the arrangement, not an afterthought. Apply the working axial load after mounting and re-check running torque; a rising torque in the first minutes signals balls climbing the washer lip under reversed thrust.
Typical equipment & failure modes
Common applications
- turntable and swivel mounts
- machine tool feed spindles with one-direction thrust
- pump impeller shafts with steady axial pull
- gear pairs generating one-direction axial force
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- hard-particle indentation in unfiltered lubricant
- thrust washer raceway wear from reverse axial shocks the one-direction thrust part cannot carry
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 60 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- Height stack-up is easy to mis-check: the thrust-washer part adds height beyond a plain needle bearing, and clamping the stack solid over it preloads the thrust set beyond its rating.
- Do not treat the axial rating 41.6 kN (Ca) as independent of radial load: the combined equivalent load formulas couple them, and a unit sized on radial life alone will spall the ball raceway first under real thrust.
- The 41.8/96.5 kN ratings and 360 g mass are SKF catalogue values transcribed from ch. 7.9 of PUB BU/P1 17000 (PDF table page 658); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
How is the NKX 60 designation read?
NKX = needle roller radial part + caged thrust ball part for a 60 mm shaft: 72 mm OD, 40 mm overall height. The caged thrust part trades some axial capacity for higher permissible speed versus NX.
Can the NKX 60 run on an unhardened shaft?
The radial needle part of the NKX 60 runs directly on the 60 mm journal — harden to 58–64 HRC and grind it. The thrust washers are integral, so no separate inner ring exists; size the shaft for the raceway tolerances in the catalogue table.
How should the NKX 60 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 60 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a NKX 60?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 60 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 6.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.9 needle roller / thrust ball, caged thrust part on 2026-09-26. Read our editorial & correction policy.