RNA4901 bearing: complete specifications & equivalents
The RNA4901 is a ISO 1206 radial bearing sized 16 x 24 x 13 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 16 mm |
| Outer diameter D | 24 mm |
| Width B | 13 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 9.9 kN |
| Basic static load rating C0 | 12.2 kN |
| Fatigue load limit Pu | 1.46 kN |
| Reference speed (thermal) | 22000 rpm |
| Limiting speed (mechanical) | 26000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 17 g |
| Manufacturer designation | RNA 4901 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & RNA-49-series range
| Bore d | 0.63 in |
|---|---|
| Outer diameter D | 0.945 in |
| Width B | 0.512 in |
| ISO bore code | 01 |
| Radial section height (D−d)/2 | 4 mm |
| Smallest bore in RNA-49-series | 14 mm |
| Largest outer diameter in RNA-49-series | 190 mm |
| Width range across RNA-49-series | 13–50 mm |
| Bore position in RNA-49-series (smallest first) | 2 of 28 |
| Bore above smallest RNA-49-series size | 2 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| RNA4901-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 16×24×13 mm envelope, but catalogue C/C0 differ between the executions (9.9/12.2 vs 8.09/9.65 kN) — boundary dimensions match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the RNA4901 model number is decoded
SKF's dimension series 49 needle roller bearings without inner ring include RNA 4901: 16 mm Fw, 24 mm outside diameter, 13 mm width — a machined and ground outer ring whose rolled flanges retain the needle rollers, running on the shaft as the inner raceway. In SKF nomenclature RNA families drop the inner ring: the numbers after the letters give the 16 mm under-roller diameter and the 13 mm width, with the 24 mm outside diameter set by the dimension series 49 needle roller bearings without inner ring plan. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Catalogue mass 17 g at 16×24×13 mm makes this one of the highest capacity-per-gram choices in the dimension series 49 needle roller bearings without inner ring; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Mounting: the flanged outer ring presses into the H7 housing bore against its flange face; the shaft (hardened to 58–64 HRC, ground) enters afterwards, and axial retention is by the housing wall plus a cover washer.
Typical equipment & failure modes
Common applications
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- cage pocket wear and roller skew after sustained operation with too little radial preload
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- rolling-contact fatigue spalling after the rated L10 life
- smearing of rollers and journal during idle periods because the radial section holds too little lubricant
Selection pitfalls — read before you substitute
- On a 16 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 24 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Reference and limiting speeds are different limits: the 22,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 16 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The 9.9/12.2 kN ratings and 17 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 626); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What mounting mistakes ruin a RNA 4901?
Press on the ring faces only with a fitting sleeve, keep everything square to the 16 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Is the RNA 4901 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Which dimensions does the RNA 4901 have?
A RNA 4901 measures 16 mm bore/Fw × 24 mm outside diameter × 13 mm width (0.63 × 0.945 × 0.512 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 9.9 kN, static C0 12.2 kN, fatigue limit Pu 1.46 kN, limiting speed 26,000 r/min, reference speed 22,000 r/min, mass about 17 g.
What does RNA 4901 mean in SKF part numbering?
RNA names a machined-ring needle roller bearing without inner ring: the figures give Fw 16 mm and width 13 mm, OD 24 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.