RNA4911 bearing: complete specifications & equivalents
The RNA4911 is a ISO 1206 radial bearing sized 63 x 80 x 25 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 63 mm |
| Outer diameter D | 80 mm |
| Width B | 25 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 57.2 kN |
| Basic static load rating C0 | 106 kN |
| Fatigue load limit Pu | 13.2 kN |
| Reference speed (thermal) | 6300 rpm |
| Limiting speed (mechanical) | 7000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 260 g |
| Manufacturer designation | RNA 4911 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & RNA-49-series range
| Bore d | 2.48 in |
|---|---|
| Outer diameter D | 3.15 in |
| Width B | 0.984 in |
| ISO bore code | 11 |
| Radial section height (D−d)/2 | 8.5 mm |
| Smallest bore in RNA-49-series | 14 mm |
| Largest outer diameter in RNA-49-series | 190 mm |
| Width range across RNA-49-series | 13–50 mm |
| Bore position in RNA-49-series (smallest first) | 15 of 28 |
| Bore above smallest RNA-49-series size | 49 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the RNA4911 model number is decoded
Where the shaft can be hardened and ground, SKF offers RNA 4911 in the dimension series 49 needle roller bearings without inner ring: outer ring only, needle rollers caged between integral flanges, 63 mm bore seat and 80 mm OD. The letters identify a flanged machined outer ring without inner ring; the figures give 63 mm Fw and 25 mm B — dimensionally identical envelopes exist with an inner ring under the NA/NKI names, which changes the shaft seat entirely. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Catalogue mass 260 g at 63×80×25 mm makes this one of the highest capacity-per-gram choices in the dimension series 49 needle roller bearings without inner ring; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- hard-particle indentation in unfiltered lubricant
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 63 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Hardness is load capacity: in families without an inner ring the 63 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The quoted 57.2/106 kN ratings are SKF catalogue values for this exact execution (RNA 4911); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- The 57.2/106 kN ratings and 260 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 632); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What are the dimensions and ratings of the RNA 4911?
A RNA 4911 measures 63 mm bore/Fw × 80 mm outside diameter × 25 mm width (2.48 × 3.15 × 0.984 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 57.2 kN, static C0 106 kN, fatigue limit Pu 13.2 kN, limiting speed 7,000 r/min, reference speed 6,300 r/min, mass about 260 g.
How is the RNA 4911 designation read?
RNA names a machined-ring needle roller bearing without inner ring: the figures give Fw 63 mm and width 25 mm, OD 80 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Can the RNA 4911 run on an unhardened shaft?
No. In this execution the 63 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the RNA 4911 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 63 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.