RNA4914 bearing: complete specifications & equivalents
The RNA4914 is a ISO 1206 radial bearing sized 80 x 100 x 30 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 80 mm |
| Outer diameter D | 100 mm |
| Width B | 30 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 84.2 kN |
| Basic static load rating C0 | 163 kN |
| Fatigue load limit Pu | 20.8 kN |
| Reference speed (thermal) | 5000 rpm |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 460 g |
| Manufacturer designation | RNA 4914 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & RNA-49-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 3.937 in |
| Width B | 1.181 in |
| ISO bore code | 14 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in RNA-49-series | 14 mm |
| Largest outer diameter in RNA-49-series | 190 mm |
| Width range across RNA-49-series | 13–50 mm |
| Bore position in RNA-49-series (smallest first) | 18 of 28 |
| Bore above smallest RNA-49-series size | 66 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the RNA4914 model number is decoded
SKF's dimension series 49 needle roller bearings without inner ring include RNA 4914: 80 mm Fw, 100 mm outside diameter, 30 mm width — a machined and ground outer ring whose rolled flanges retain the needle rollers, running on the shaft as the inner raceway. In SKF nomenclature RNA families drop the inner ring: the numbers after the letters give the 80 mm under-roller diameter and the 30 mm width, with the 100 mm outside diameter set by the dimension series 49 needle roller bearings without inner ring plan. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Catalogue mass 460 g at 80×100×30 mm makes this one of the highest capacity-per-gram choices in the dimension series 49 needle roller bearings without inner ring; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- cage pocket wear and roller skew after sustained operation with too little radial preload
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- electrical erosion on VFD-driven shafts without brush or insulated mounting
- smearing of rollers and journal during idle periods because the radial section holds too little lubricant
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 80 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- Do not interchange envelope-identical needle families blindly: RNA 4914 shares its 80×100×30 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- The 84.2/163 kN ratings and 460 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 634); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Does the RNA 4914 need a hardened and ground shaft?
No. In this execution the 80 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a RNA 4914?
Press on the ring faces only with a fitting sleeve, keep everything square to the 80 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Is the RNA 4914 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Which dimensions does the RNA 4914 have?
A RNA 4914 measures 80 mm bore/Fw × 100 mm outside diameter × 30 mm width (3.15 × 3.937 × 1.181 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 84.2 kN, static C0 163 kN, fatigue limit Pu 20.8 kN, limiting speed 5,600 r/min, reference speed 5,000 r/min, mass about 460 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.