22210EAD1 bearing: complete specifications & equivalents
The 22210EAD1 is a ISO 15 radial bearing sized 50 x 90 x 23 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 50 mm |
| Outer diameter D | 90 mm |
| Width B | 23 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 130 kN |
| Basic static load rating C0 | 124 kN |
| Fatigue load limit Pu | 10.1 kN |
| Limiting speed (mechanical) | 5700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 614 g |
| Manufacturer designation | NTN 22210EAD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22200-series range
| Bore d | 1.969 in |
|---|---|
| Outer diameter D | 3.543 in |
| Width B | 0.906 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 20 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 580 mm |
| Width range across 22200-series | 18–150 mm |
| Bore position in 22200-series (smallest first) | 6 of 32 |
| Bore above smallest 22200-series size | 25 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22210EAKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22200-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 22210EAKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22210EAD1 model number is decoded
The NTN order number 22210EAD1 identifies a 50×90×23 mm (1.969 × 3.543 × 0.906 in) spherical roller bearing, cylindrical bore, to the ISO 15 boundary plan. Digit by digit the code reads as spherical-roller dimension series plus 50 mm bore; the 23 mm width is the wide ISO 15 section, which is why spherical rollers interchange dimensionally but not in cage or rating detail. At 130 kN C and 614 g mass the 22200 series part is built for shock and vibration; the 23 mm-wide ring needs square abutments to keep both rows equally loaded. The 20.0 mm section height hosts the spherical roller geometry; shaft and housing fillet radii must clear the chamfer table so the 23 mm-wide ring seats fully on both sides. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- pump and fan shafts under heavy belt load
- marine propulsion auxiliary shafts
- vibrating screen and feeder shafts
- industrial gearbox and reducer shafts
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- rolling-contact fatigue after the catalogue L10 life at the actual load
- water-induced pitting in washdown or outdoor duty without effective external seals
Selection pitfalls — read before you substitute
- Vibrating-duty 50 mm bearings need the right clearance class and secure fits; verify the k5/m5 seat and relubrication routing rather than assuming the open 22210EAD1 is greased for life.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 5,700 r/min grease rating is lost to abrasive wear long before fatigue.
- Minimum load must be maintained even at rest under vibration: an unloaded 22210EAD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- Never substitute 22210EAD1 by envelope alone: the 124 kN C0 and 10.1 kN Pu are specific to the NTN EA pressed-steel-cage execution, and vibrating duty depends heavily on cage identity.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 5,700 r/min grease rating is lost to abrasive wear long before fatigue.
- The 130/124 kN ratings, 10.1 kN Pu and 614 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22210EAD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22210EAD1?
22210EAD1 is an NTN double-row spherical roller bearing to ISO 15: 50 mm bore, 90 mm OD and 23 mm width (1.969 × 3.543 × 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 130 kN, C0 124 kN, Pu 10.1 kN, grease limiting speed 5,700 r/min, oil 7,200 r/min, mass about 614 g. It is open, with pressed sheet-steel window cage (EA high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
22210EAD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 22210EAKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22210EAD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22210EAD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22210EAD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22210EAD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22200 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 130 kN C / 124 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.