22224EAKD1 bearing: complete specifications & equivalents
The 22224EAKD1 is a ISO 15 radial bearing sized 120 x 215 x 58 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 120 mm |
| Outer diameter D | 215 mm |
| Width B | 58 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 688 kN |
| Basic static load rating C0 | 753 kN |
| Fatigue load limit Pu | 49.9 kN |
| Limiting speed (mechanical) | 2400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 8680 g |
| Manufacturer designation | NTN 22224EAKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22200-series range
| Bore d | 4.724 in |
|---|---|
| Outer diameter D | 8.465 in |
| Width B | 2.283 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 47.5 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 580 mm |
| Width range across 22200-series | 18–150 mm |
| Bore position in 22200-series (smallest first) | 18 of 32 |
| Bore above smallest 22200-series size | 95 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22224EAD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22200-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 22224EAD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22224EAKD1 model number is decoded
22224EAKD1 is an NTN double-row spherical roller bearing: two rows of symmetric rollers on a sphered outer raceway, 120×215×58 mm to ISO 15, with pressed sheet-steel window cage (EA high-capacity design). Digit by digit the code reads as spherical-roller dimension series plus 120 mm bore; the 58 mm width is the wide ISO 15 section, which is why spherical rollers interchange dimensionally but not in cage or rating detail. NTN prints two speeds for 22224EAKD1: 2,400 r/min grease and 3,000 r/min oil — the gap of 600 r/min reflects oil cooling of the heavy roller set. 120 mm bore is 4.724 in and 215 mm OD is 8.465 in; the ISO 15 envelope swaps between brands, but the 688/753 kN ratings and cage design are NTN 2203E values. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- brinelling from static overload or a hammer blow during sleeve mounting
- hard-particle indentation through the open arrangement in dusty mining duty
Selection pitfalls — read before you substitute
- At 120 mm bore 22224EAKD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Do not confuse EA and EM at the same number: 22224EAKD1 carries EA pressed-steel-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 120×215 mm envelope is identical.
- Minimum load must be maintained even at rest under vibration: an unloaded 22224EAKD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 120 mm bearing, and drive-up procedures differ.
- Oil relubrication toward 3,000 r/min needs drain and level design; flooding the 58 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- The 688/753 kN ratings, 49.9 kN Pu and 8680 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22224EAKD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22224EAKD1?
22224EAKD1 is an NTN double-row spherical roller bearing to ISO 15: 120 mm bore, 215 mm OD and 58 mm width (4.724 × 8.465 × 2.283 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 688 kN, C0 753 kN, Pu 49.9 kN, grease limiting speed 2,400 r/min, oil 3,000 r/min, mass about 8680 g. It is open, with pressed sheet-steel window cage (EA high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 22224EAKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 22224EAD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22224EAKD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22224EAKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22224EAKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22224EAKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22200 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 688 kN C / 753 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.