22316EMD1 bearing: complete specifications & equivalents
The 22316EMD1 is a ISO 15 radial bearing sized 80 x 170 x 58 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 80 mm |
| Outer diameter D | 170 mm |
| Width B | 58 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 541 kN |
| Basic static load rating C0 | 522 kN |
| Fatigue load limit Pu | 32.5 kN |
| Limiting speed (mechanical) | 2700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 6280 g |
| Manufacturer designation | NTN 22316EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22300-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 6.693 in |
| Width B | 2.283 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 45 mm |
| Smallest bore in 22300-series | 40 mm |
| Largest outer diameter in 22300-series | 620 mm |
| Width range across 22300-series | 33–185 mm |
| Bore position in 22300-series (smallest first) | 9 of 28 |
| Bore above smallest 22300-series size | 40 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22316EMKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22300-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 22316EMKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22316EMD1 model number is decoded
For heavy radial load with misalignment on a 80 mm shaft, NTN supplies 22316EMD1: sphered outer raceway, two roller rows, one-piece machined brass cage (EM high-capacity design), oil speed 3,400 r/min. Digit by digit the code reads as spherical-roller dimension series plus 80 mm bore; the 58 mm width is the wide ISO 15 section, which is why spherical rollers interchange dimensionally but not in cage or rating detail. At 541 kN C and 6280 g mass the 22300 series part is built for shock and vibration; the 58 mm-wide ring needs square abutments to keep both rows equally loaded. Grease/oil ratio: the 2,700 r/min limiting value is .79 of the 3,400 r/min oil value; heavy 58 mm-wide cages run hot in churning grease, so quantity and groove supply both matter. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- cement-mill and kiln auxiliary drives
- large gearbox and marine gear shafts
- wind-turbine gearbox and rotor bearings
- large vibrating screens and mining feeders
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- brinelling from static overload or a hammer blow during sleeve mounting
Selection pitfalls — read before you substitute
- Mount the 80 mm ring with induction heat or the sleeve drive-up procedure; at 6280 g cocking damages the spherical raceways, and repositioning after seating is impractical.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 80 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K seats.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 80 mm bearing, and drive-up procedures differ.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 2,700 r/min grease rating is lost to abrasive wear long before fatigue.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 2,700 r/min grease rating is lost to abrasive wear long before fatigue.
- The 541/522 kN ratings, 32.5 kN Pu and 6280 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22316EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22316EMD1?
22316EMD1 is an NTN double-row spherical roller bearing to ISO 15: 80 mm bore, 170 mm OD and 58 mm width (3.15 × 6.693 × 2.283 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 541 kN, C0 522 kN, Pu 32.5 kN, grease limiting speed 2,700 r/min, oil 3,400 r/min, mass about 6280 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
22316EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 22316EMKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22316EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22316EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22316EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22316EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22300 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 541 kN C / 522 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.