23026-CCK-W33 bearing: complete specifications & equivalents
The 23026-CCK-W33 is a ISO 15 radial bearing sized 130 x 200 x 52 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 130 mm |
| Outer diameter D | 200 mm |
| Width B | 52 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 452 kN |
| Basic static load rating C0 | 610 kN |
| Fatigue load limit Pu | 61 kN |
| Reference speed (thermal) | 2800 rpm |
| Limiting speed (mechanical) | 3600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 8600 g |
| Manufacturer designation | SKF 23026 CCK/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23000-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 7.874 in |
| Width B | 2.047 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 480 mm |
| Width range across 23000-series | 27–121 mm |
| Bore position in 23000-series (smallest first) | 10 of 23 |
| Bore above smallest 23000-series size | 60 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23026 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) sleeve-mounted execution of 23026; identical ISO 15 envelope, fits H3026 adapter sleeve on a 110 mm shaft. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23026-CCK-W33 model number is decoded
Ordering number SKF 23026 CCK/W33 in SKF catalogue PUB BU/P1 17000 is a double-row spherical roller bearing with a tapered bore (1:12), intended for an H-series adapter sleeve or AH withdrawal sleeve, with two pressed-steel cages with a floating guide ring and the same 130×200×52 mm ISO 15 outline as its cylindrical-bore counterpart. Reading the designation: the leading 2 marks a spherical roller bearing, the 30 is the ISO 15 dimension series (dimension series 30 (slim OD, extra-wide)), and the last two digits encode the 130 mm bore; the 200 mm OD and 52 mm width follow the ISO 15 general plan. Sleeve mounting is why the K execution exists: a plain h9-tolerance shaft is enough because the adapter sleeve supplies the precision seat, and the bearing is removable without pulling over an interference journal — a separate order number from the cylindrical-bore bearing, never a field conversion. The 61 kN Pu figure feeds the adjusted-life equation at contaminated or partial-film conditions, and the 1.35 C0/C balance shows this execution is tuned to heavy radial-plus-axial duty with misalignment tolerance. For shafts with a locating shoulder, use an AH withdrawal sleeve instead of an adapter sleeve: the bearing presses against the shoulder and the sleeve is drawn out for dismounting, making the 23026-cck-w33 removable without an induction heater.
Typical equipment & failure modes
Common applications
- steel-plant continuous-caster segments
- large induced-draft fan rotors
- long through-shafts in conveyors, where a sleeve seat avoids a precision journal
- stepped shafts fitted with withdrawal sleeves against a fixed shoulder
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- inner-ring circumferential cracking after over-drive on the tapered seat removes too much radial clearance and the bearing runs preloaded
- roller-end scoring from starved lubricant at start-up before the grease channel purges
- false brinelling on standby machines exposed to external vibration
Selection pitfalls — read before you substitute
- At 130 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23000-series series at 130 mm bore (200×52 mm) is the slim-OD envelope: it buys radial space but gives up capacity against a 222-series bearing of the same bore — confirm the L10 margin before downsizing into it.
- The 23026-cck-w33 and its cylindrical-bore counterpart 23026-cc-w33 share envelope and load ratings (452/610 kN) but are not interchangeable in a housing already fitted for direct shaft mounting — the sleeve changes the assembly stack-up.
- Never apply the drive-up or clearance-reduction figures for this 1:12 tapered 23026-cck-w33 to a bearing of the other taper (1:12 vs 1:30); the steeper taper moves far less clearance per nut turn and the targets come from different catalogue tables.
- The 23026-cck-w33 shares its ISO 15 envelope across brands, but internal geometry differs — SKF load ratings in this row are 452/610 kN; another maker's same-size bearing may rate higher or lower, so do not interchange on envelope alone.
- The 452/610 kN ratings are SKF catalogue values for this tapered-bore execution (SKF 23026 CCK/W33); sleeve, KM nut and MB washer are separate order numbers, and the catalogue version (SKF catalogue PUB BU/P1 17000) should travel with the mounting specification.
Frequently asked questions
What are the dimensions and catalogue data of 23026-cck-w33?
The SKF 23026 CCK/W33 is a double-row spherical roller bearing with a 1:12 tapered bore, 130 mm nominal bore, 200 mm outer diameter and 52 mm width (5.118 × 7.874 × 2.047 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: C 452 kN, C0 610 kN, Pu 61 kN, reference speed 2,800 r/min, limiting speed 3,600 r/min, mass about 8600 g. It is mounted on an adapter (H) or withdrawal (AH) sleeve, not directly on the shaft.
What does the K suffix mean on 23026-cck-w33?
K marks a 1:12 tapered bore for sleeve mounting — SKF writes EK or CCK(/W33), FAG writes -K- inside the suffix chain for sleeve mounting. The bearing seats on an H-series adapter sleeve with a KM locknut and MB lock washer (plain shaft, h9 tolerance), or on an AH withdrawal sleeve against a shaft shoulder. The rarer K30 suffix would instead mean a 1:30 taper; dimension series 40/41 spherical rollers commonly use it.
Which adapter sleeve fits the 23026-cck-w33?
The sleeve is selected by the actual shaft diameter in millimetres, not only by the 130 mm nominal bore: SKF H-sleeve numbers each cover a small shaft-diameter range and are width-series specific (H39/H30/H31/H32 matching dimension series 39/40/31/32), and each kit bundles the sleeve, KM locknut and MB lock washer. For shoulder locations use an AH withdrawal sleeve instead. Confirm the sleeve number against the SKF catalogue PUB BU/P1 17000 mounting tables for your shaft size.
How is the 23026-cck-w33 driven up and checked?
Mounting is controlled by radial-clearance reduction or axial drive-up distance from the SKF catalogue tables for the 1:12 taper, never by locknut torque. Measure clearance with feeler gauges before and after tightening the KM nut, stop at the tabulated decrease, and lock the MB washer tab. Over-drive removes too much clearance (inner-ring cracking risk); under-drive lets the sleeve creep and fret.
What is the difference between 23026-cck-w33 and 23026-cc-w33?
They share the ISO 15 envelope and the same 452/610 kN ratings, but 23026-cck-w33 has the 1:12 tapered bore for sleeve mounting on a plain shaft, while 23026-cc-w33 has a cylindrical bore for direct mounting on a machined interference journal (typically m6 with H7 housing). They are separate order numbers, not interchangeable in the same shaft arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions on 2026-09-26. Read our editorial & correction policy.