23026EMD1 bearing: complete specifications & equivalents
The 23026EMD1 is a ISO 15 radial bearing sized 130 x 200 x 52 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 130 mm |
| Outer diameter D | 200 mm |
| Width B | 52 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 565 kN |
| Basic static load rating C0 | 721 kN |
| Fatigue load limit Pu | 44.2 kN |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 5900 g |
| Manufacturer designation | NTN 23026EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23000-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 7.874 in |
| Width B | 2.047 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 1580 mm |
| Width range across 23000-series | 27–345 mm |
| Bore position in 23000-series (smallest first) | 10 of 46 |
| Bore above smallest 23000-series size | 60 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23026EMKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23026EMKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23026EMD1 model number is decoded
The NTN order number 23026EMD1 identifies a 130×200×52 mm (5.118 × 7.874 × 2.047 in) spherical roller bearing, cylindrical bore, to the ISO 15 boundary plan. Numbering ties 23026EMD1 to its envelope and execution: same-number EA versus EM or plain variants share the 130 mm bore but differ in cage and sometimes mass, so they are quoted as separate articles. Suffix reading on 23026EMD1: EM identifies the high-capacity execution with a one-piece machined brass cage; the ＊ symbol in 2203E marks the ULTAGE new-generation specification (not part of the order code); and D1 provides the outer-ring lubrication feature; quote the full code because each suffix is a distinct article. Equivalent-load planning keeps a radial plus moderate axial combination on 23026EMD1; if the axial component dominates, pair with a thrust bearing rather than running one roller row unloaded. Fit the cylindrical-bore 23026EMD1 with the inner ring heated (max 120 °C) for the shaft interference; the outer ring slides into the housing with its spherical seat able to pivot after seating.
Typical equipment & failure modes
Common applications
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- pressed EA cage fatigue under sustained vibration when minimum load is not maintained
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- brinelling from static overload or a hammer blow during sleeve mounting
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
Selection pitfalls — read before you substitute
- At 130 mm bore 23026EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 130 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K seats.
- Minimum load must be maintained even at rest under vibration: an unloaded 23026EMD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 52 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 52 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- The 565/721 kN ratings, 44.2 kN Pu and 5900 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23026EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23026EMD1?
23026EMD1 is an NTN double-row spherical roller bearing to ISO 15: 130 mm bore, 200 mm OD and 52 mm width (5.118 × 7.874 × 2.047 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 565 kN, C0 721 kN, Pu 44.2 kN, grease limiting speed 2,200 r/min, oil 2,900 r/min, mass about 5900 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23026EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23026EMKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23026EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23026EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23026EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23026EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 565 kN C / 721 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.