23028EAD1 bearing: complete specifications & equivalents
The 23028EAD1 is a ISO 15 radial bearing sized 140 x 210 x 53 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 140 mm |
| Outer diameter D | 210 mm |
| Width B | 53 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 597 kN |
| Basic static load rating C0 | 783 kN |
| Fatigue load limit Pu | 47.5 kN |
| Limiting speed (mechanical) | 2100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 6320 g |
| Manufacturer designation | NTN 23028EAD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23000-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 8.268 in |
| Width B | 2.087 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 1580 mm |
| Width range across 23000-series | 27–345 mm |
| Bore position in 23000-series (smallest first) | 11 of 46 |
| Bore above smallest 23000-series size | 70 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23028EAKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23028EAKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23028EAD1 model number is decoded
23028EAD1 is an NTN double-row spherical roller bearing: two rows of symmetric rollers on a sphered outer raceway, 140×210×53 mm to ISO 15, with pressed sheet-steel window cage (EA high-capacity design). The leading digits are the ISO 15 dimension series (23000 series); the bore code resolves to 140 mm (two-digit code ×5, with the 00–03 exception table), and 210 mm OD / 53 mm width follow the general plan. The 35.0 mm radial section over the 140 mm bore carries two roller rows; capacity per millimetre of bore is about 4.3 kN/mm, among the highest of rolling bearings for the ISO 15 envelope. 140 mm bore is 5.512 in and 210 mm OD is 8.268 in; the ISO 15 envelope swaps between brands, but the 597/783 kN ratings and cage design are NTN 2203E values. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 23028EAD1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
- cement-rotary-kiln support and trunnion rolls
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
Selection pitfalls — read before you substitute
- At 140 mm bore 23028EAD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 140 mm bearing, and drive-up procedures differ.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 140 mm bearing, and drive-up procedures differ.
- Never substitute 23028EAD1 by envelope alone: the 783 kN C0 and 47.5 kN Pu are specific to the NTN EA pressed-steel-cage execution, and vibrating duty depends heavily on cage identity.
- The cylindrical-bore 23028EAD1 and its tapered-bore counterpart 23028EAKD1 share envelope and ratings but not mounting: do not order the K variant unless the drawing specifies a sleeve or tapered seat.
- The 597/783 kN ratings, 47.5 kN Pu and 6320 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23028EAD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23028EAD1?
23028EAD1 is an NTN double-row spherical roller bearing to ISO 15: 140 mm bore, 210 mm OD and 53 mm width (5.512 × 8.268 × 2.087 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 597 kN, C0 783 kN, Pu 47.5 kN, grease limiting speed 2,100 r/min, oil 2,700 r/min, mass about 6320 g. It is open, with pressed sheet-steel window cage (EA high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23028EAD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23028EAKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23028EAD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23028EAD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23028EAD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23028EAD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 597 kN C / 783 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.