23040-CCK-W33 bearing: complete specifications & equivalents
The 23040-CCK-W33 is a ISO 15 radial bearing sized 200 x 310 x 82 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 200 mm |
| Outer diameter D | 310 mm |
| Width B | 82 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1058 kN |
| Basic static load rating C0 | 1530 kN |
| Fatigue load limit Pu | 137 kN |
| Reference speed (thermal) | 1800 rpm |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 31500 g |
| Manufacturer designation | SKF 23040 CCK/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23000-series range
| Bore d | 7.874 in |
|---|---|
| Outer diameter D | 12.205 in |
| Width B | 3.228 in |
| ISO bore code | 40 |
| Radial section height (D−d)/2 | 55 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 480 mm |
| Width range across 23000-series | 27–121 mm |
| Bore position in 23000-series (smallest first) | 17 of 23 |
| Bore above smallest 23000-series size | 130 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23040 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) sleeve-mounted execution of 23040; identical ISO 15 envelope, fits H3040 adapter sleeve on a 180 mm shaft. |
| C3040 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF CARB toroidal bearing C 3040 shares the 200×310×82 mm envelope but catalogue C/C0 differ (1120/1730 kN vs 1058/1530 kN); it floats axially and cannot locate the shaft — pair, never swap one-for-one. |
| C3040-K | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF CARB toroidal bearing C 3040 K shares the 200×310×82 mm envelope but catalogue C/C0 differ (1120/1730 kN vs 1058/1530 kN); it floats axially and cannot locate the shaft — pair, never swap one-for-one. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23040-CCK-W33 model number is decoded
23040-cck-w33 is the 1:12 tapered-bore execution of the 23000-series spherical roller bearing: the same two barrel-roller rows on a sphered outer raceway as 23040-cc-w33, but the inner-ring bore tapers 1 mm per 12 mm for adapter- or withdrawal-sleeve mounting, as listed by SKF in SKF catalogue PUB BU/P1 17000. Numbering ties the bearing to its envelope: 23040-cck-w33 means spherical-roller type, dimension series 30, 200 mm bore — which is why the 310×82 mm outline swaps dimensionally with other ISO 15 bearings of the same code. The K in the designation marks the 1:12 tapered bore: SKF mounts it on an H-series adapter sleeve (with KM locknut and MB lock washer) on a plain commercial-grade shaft, or on an AH withdrawal sleeve where the bearing must abut a shaft shoulder. The 137 kN Pu figure feeds the adjusted-life equation at contaminated or partial-film conditions, and the 1.45 C0/C balance shows this execution is tuned to heavy radial-plus-axial duty with misalignment tolerance. On an H adapter sleeve the 200 mm shaft seat only needs an h9 plain journal; slide the sleeve into the 23040-cck-w33 inner ring, tighten the KM nut against the MB washer until the catalogue clearance-reduction value is reached, then lock the washer tab.
Typical equipment & failure modes
Common applications
- steel-plant continuous-caster segments
- large induced-draft fan rotors
- long through-shafts in conveyors, where a sleeve seat avoids a precision journal
- stepped shafts fitted with withdrawal sleeves against a fixed shoulder
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- inner-ring circumferential cracking after over-drive on the tapered seat removes too much radial clearance and the bearing runs preloaded
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- At 200 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23000-series series at 200 mm bore (310×82 mm) is the slim-OD envelope: it buys radial space but gives up capacity against a 222-series bearing of the same bore — confirm the L10 margin before downsizing into it.
- The adapter sleeve is selected by actual shaft diameter, not by the 200 mm nominal bearing bore: H-sleeve part numbers span a small diameter range, so two different shaft diameters can use the same 23040-cck-w33 with different sleeves.
- The adapter sleeve is selected by actual shaft diameter, not by the 200 mm nominal bearing bore: H-sleeve part numbers span a small diameter range, so two different shaft diameters can use the same 23040-cck-w33 with different sleeves.
- Catalogue reference speed and limiting speed are different limits: the 1,800 r/min reference is a thermal criterion under load, while the 2,200 r/min limiting value is the mechanical ceiling — observe both.
- The 1058/1530 kN ratings are SKF catalogue values for this tapered-bore execution (SKF 23040 CCK/W33); sleeve, KM nut and MB washer are separate order numbers, and the catalogue version (SKF catalogue PUB BU/P1 17000) should travel with the mounting specification.
Frequently asked questions
What are the dimensions and catalogue data of 23040-cck-w33?
The SKF 23040 CCK/W33 is a double-row spherical roller bearing with a 1:12 tapered bore, 200 mm nominal bore, 310 mm outer diameter and 82 mm width (7.874 × 12.205 × 3.228 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: C 1058 kN, C0 1530 kN, Pu 137 kN, reference speed 1,800 r/min, limiting speed 2,200 r/min, mass about 31500 g. It is mounted on an adapter (H) or withdrawal (AH) sleeve, not directly on the shaft.
What does the K suffix mean on 23040-cck-w33?
K marks a 1:12 tapered bore for sleeve mounting — SKF writes EK or CCK(/W33), FAG writes -K- inside the suffix chain for sleeve mounting. The bearing seats on an H-series adapter sleeve with a KM locknut and MB lock washer (plain shaft, h9 tolerance), or on an AH withdrawal sleeve against a shaft shoulder. The rarer K30 suffix would instead mean a 1:30 taper; dimension series 40/41 spherical rollers commonly use it.
Which adapter sleeve fits the 23040-cck-w33?
The sleeve is selected by the actual shaft diameter in millimetres, not only by the 200 mm nominal bore: SKF H-sleeve numbers each cover a small shaft-diameter range and are width-series specific (H39/H30/H31/H32 matching dimension series 39/40/31/32), and each kit bundles the sleeve, KM locknut and MB lock washer. For shoulder locations use an AH withdrawal sleeve instead. Confirm the sleeve number against the SKF catalogue PUB BU/P1 17000 mounting tables for your shaft size.
How is the 23040-cck-w33 driven up and checked?
Mounting is controlled by radial-clearance reduction or axial drive-up distance from the SKF catalogue tables for the 1:12 taper, never by locknut torque. Measure clearance with feeler gauges before and after tightening the KM nut, stop at the tabulated decrease, and lock the MB washer tab. Over-drive removes too much clearance (inner-ring cracking risk); under-drive lets the sleeve creep and fret.
What is the difference between 23040-cck-w33 and 23040-cc-w33?
They share the ISO 15 envelope and the same 1058/1530 kN ratings, but 23040-cck-w33 has the 1:12 tapered bore for sleeve mounting on a plain shaft, while 23040-cc-w33 has a cylindrical bore for direct mounting on a machined interference journal (typically m6 with H7 housing). They are separate order numbers, not interchangeable in the same shaft arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions on 2026-09-26. Read our editorial & correction policy.