23044-CCK-W33 bearing: complete specifications & equivalents
The 23044-CCK-W33 is a ISO 15 radial bearing sized 220 x 340 x 90 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 220 mm |
| Outer diameter D | 340 mm |
| Width B | 90 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1261 kN |
| Basic static load rating C0 | 1860 kN |
| Fatigue load limit Pu | 163 kN |
| Reference speed (thermal) | 1600 rpm |
| Limiting speed (mechanical) | 2000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 39500 g |
| Manufacturer designation | SKF 23044 CCK/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23000-series range
| Bore d | 8.661 in |
|---|---|
| Outer diameter D | 13.386 in |
| Width B | 3.543 in |
| ISO bore code | 44 |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 480 mm |
| Width range across 23000-series | 27–121 mm |
| Bore position in 23000-series (smallest first) | 18 of 23 |
| Bore above smallest 23000-series size | 150 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23044 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) sleeve-mounted execution of 23044; identical ISO 15 envelope, fits OH3044 adapter sleeve on a 200 mm shaft. |
| C3044 | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3044 shares the 220×340×90 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
| C3044-K | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3044 K shares the 220×340×90 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23044-CCK-W33 model number is decoded
The SKF 23044 CCK/W33 is a 220×340×90 mm spherical roller bearing with a 1:12 tapered bore — SKF catalogue execution for sleeve mounting on a 220 mm plain shaft, retaining the double-row self-aligning barrel-roller design. Digit by digit, 23044-cck-w33 reads as bearing type 2 (spherical roller, two barrel-roller rows), dimension series 30, and bore reference 44 resolving to 220 mm; 340 mm OD and 90 mm width are the matching ISO 15 boundary values. Reading the suffix on 23044-cck-w33, the K (or EK/CCK) element changes only the bore — 1:12 taper for sleeve mounting — while the rest of the suffix chain (CC cages with W33 groove) keeps the same internal design, cage and W33 relubrication features as the cylindrical-bore 23044-cc-w33. Catalogue mass 39500 g for the 220×340×90 mm open execution covers the two pressed-steel cages with a floating guide ring; tapered-bore and sealed variants differ in mass and carry their own order numbers. Because driving up the 1:12 taper consumes radial clearance, K executions are commonly ordered with C3 initial clearance so the residual running clearance after mounting matches the cylindrical-bore 23044-cc-w33 on an interference seat.
Typical equipment & failure modes
Common applications
- large dredger and marine winch drums
- steel-plant continuous-caster segments
- shafting produced to commercial tolerances, where the adapter sleeve supplies the precision seat
- split-housing plummer block arrangements with bearings swapped in situ
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- fretting corrosion and sleeve-seat scoring when drive-up is insufficient and the tapered inner ring creeps on the adapter sleeve
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- smearing on the roller-raceway contact during skid starts below the minimum load
Selection pitfalls — read before you substitute
- At 220 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23000-series series at 220 mm bore (340×90 mm) is the slim-OD envelope: it buys radial space but gives up capacity against a 222-series bearing of the same bore — confirm the L10 margin before downsizing into it.
- The adapter sleeve is selected by actual shaft diameter, not by the 220 mm nominal bearing bore: H-sleeve part numbers span a small diameter range, so two different shaft diameters can use the same 23044-cck-w33 with different sleeves.
- The adapter sleeve is selected by actual shaft diameter, not by the 220 mm nominal bearing bore: H-sleeve part numbers span a small diameter range, so two different shaft diameters can use the same 23044-cck-w33 with different sleeves.
- Catalogue reference speed and limiting speed are different limits: the 1,600 r/min reference is a thermal criterion under load, while the 2,000 r/min limiting value is the mechanical ceiling — observe both.
- The 1261/1860 kN ratings are SKF catalogue values for this tapered-bore execution (SKF 23044 CCK/W33); sleeve, KM nut and MB washer are separate order numbers, and the catalogue version (SKF catalogue PUB BU/P1 17000) should travel with the mounting specification.
Frequently asked questions
What are the dimensions and catalogue data of 23044-cck-w33?
The SKF 23044 CCK/W33 is a double-row spherical roller bearing with a 1:12 tapered bore, 220 mm nominal bore, 340 mm outer diameter and 90 mm width (8.661 × 13.386 × 3.543 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: C 1261 kN, C0 1860 kN, Pu 163 kN, reference speed 1,600 r/min, limiting speed 2,000 r/min, mass about 39500 g. It is mounted on an adapter (H) or withdrawal (AH) sleeve, not directly on the shaft.
What does the K suffix mean on 23044-cck-w33?
K marks a 1:12 tapered bore for sleeve mounting — SKF writes EK or CCK(/W33), FAG writes -K- inside the suffix chain for sleeve mounting. The bearing seats on an H-series adapter sleeve with a KM locknut and MB lock washer (plain shaft, h9 tolerance), or on an AH withdrawal sleeve against a shaft shoulder. The rarer K30 suffix would instead mean a 1:30 taper; dimension series 40/41 spherical rollers commonly use it.
Which adapter sleeve fits the 23044-cck-w33?
The sleeve is selected by the actual shaft diameter in millimetres, not only by the 220 mm nominal bore: SKF H-sleeve numbers each cover a small shaft-diameter range and are width-series specific (H39/H30/H31/H32 matching dimension series 39/40/31/32), and each kit bundles the sleeve, KM locknut and MB lock washer. For shoulder locations use an AH withdrawal sleeve instead. Confirm the sleeve number against the SKF catalogue PUB BU/P1 17000 mounting tables for your shaft size.
How is the 23044-cck-w33 driven up and checked?
Mounting is controlled by radial-clearance reduction or axial drive-up distance from the SKF catalogue tables for the 1:12 taper, never by locknut torque. Measure clearance with feeler gauges before and after tightening the KM nut, stop at the tabulated decrease, and lock the MB washer tab. Over-drive removes too much clearance (inner-ring cracking risk); under-drive lets the sleeve creep and fret.
What is the difference between 23044-cck-w33 and 23044-cc-w33?
They share the ISO 15 envelope and the same 1261/1860 kN ratings, but 23044-cck-w33 has the 1:12 tapered bore for sleeve mounting on a plain shaft, while 23044-cc-w33 has a cylindrical bore for direct mounting on a machined interference journal (typically m6 with H7 housing). They are separate order numbers, not interchangeable in the same shaft arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions on 2026-09-26. Read our editorial & correction policy.