231-750B bearing: complete specifications & equivalents
The 231-750B is a ISO 15 radial bearing sized 750 x 1220 x 365 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 750 mm |
| Outer diameter D | 1220 mm |
| Width B | 365 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 14300 kN |
| Basic static load rating C0 | 27200 kN |
| Fatigue load limit Pu | 1130 kN |
| Limiting speed (mechanical) | 200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1700000 g |
| Manufacturer designation | NTN 231/750B |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 29.528 in |
|---|---|
| Outer diameter D | 48.031 in |
| Width B | 14.37 in |
| ISO bore code | 31 |
| Radial section height (D−d)/2 | 235 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 33 of 36 |
| Bore above smallest 23100-series size | 650 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 231-750BK | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 231-750BK (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 231-750B model number is decoded
NTN lists 231/750B with a cylindrical bore and plain outer ring (no D1/W33 groove): 750 mm bore, 1220 mm OD, 365 mm width, rated 200 r/min on grease. Reading the full code: the number gives the 750×1220 mm envelope, — names the cage/capacity execution, no bore suffix means cylindrical bore for a direct shaft seat, and plain outer ring (no D1/W33 groove) completes the order number. The bearing accepts predominantly radial load with a moderate axial share, but is not a pure thrust bearing: sustained axial-only load skids the unloaded row and damages the basic cage. 750 mm bore is 29.528 in and 1220 mm OD is 48.031 in; the ISO 15 envelope swaps between brands, but the 14300/27200 kN ratings and cage design are NTN 2203E values. Fit the cylindrical-bore 231/750B with the inner ring heated (max 120 °C) for the shaft interference; the outer ring slides into the housing with its spherical seat able to pivot after seating.
Typical equipment & failure modes
Common applications
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- micro-pitting when the EHL film is thinner than the raceway composite roughness
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- hard-particle indentation through the open arrangement in dusty mining duty
Selection pitfalls — read before you substitute
- At 750 mm bore 231/750B is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 365 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- Never substitute 231/750B by envelope alone: the 27200 kN C0 and 1130 kN Pu are specific to the NTN basic execution, and vibrating duty depends heavily on cage identity.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 750 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K30 seats.
- Never substitute 231/750B by envelope alone: the 27200 kN C0 and 1130 kN Pu are specific to the NTN basic execution, and vibrating duty depends heavily on cage identity.
- The 14300/27200 kN ratings, 1130 kN Pu and 1700000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 231/750B (basic); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 231/750B?
231/750B is an NTN double-row spherical roller bearing to ISO 15: 750 mm bore, 1220 mm OD and 365 mm width (29.528 × 48.031 × 14.37 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 14300 kN, C0 27200 kN, Pu 1130 kN, grease limiting speed 200 r/min, oil 260 r/min, mass about 1700000 g. It is open, with pressed-steel cage (standard execution).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
231/750B has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 231/750BK (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 231/750B is the basic execution.
What do D1 and W33 mean on 231/750B?
231/750B is listed without a D1/W33 outer-ring groove in 2203E; lubrication is supplied from the ring sides. D1 (NTN spelling) and W33 add the annular groove plus holes and are ordered as distinct suffixed executions of the same envelope.
How much misalignment and axial load can 231/750B take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 14300 kN C / 27200 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.