23132 bearing: complete specifications & equivalents
The 23132 is a ISO 15 radial bearing sized 160 x 270 x 86 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 160 mm |
| Outer diameter D | 270 mm |
| Width B | 86 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1029 kN |
| Basic static load rating C0 | 1370 kN |
| Fatigue load limit Pu | 129 kN |
| Reference speed (thermal) | 1900 rpm |
| Limiting speed (mechanical) | 2400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 20500 g |
| Manufacturer designation | SKF 23132 CC/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23100-series range
| Bore d | 6.299 in |
|---|---|
| Outer diameter D | 10.63 in |
| Width B | 3.386 in |
| ISO bore code | 32 |
| Radial section height (D−d)/2 | 55 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 790 mm |
| Width range across 23100-series | 52–248 mm |
| Bore position in 23100-series (smallest first) | 7 of 25 |
| Bore above smallest 23100-series size | 60 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23132 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; D/B cross-verified against Schaeffler HR1 2022; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
| 23132-CCK-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) execution on H3132 adapter sleeve; same ISO 15 envelope, separate order number. |
| C3132 | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3132 shares the 160×270×86 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
| C3132-K | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3132 K shares the 160×270×86 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23132 model number is decoded
In SKF catalogue PUB BU/P1 17000, 23132 appears as 23132 CC/W33: an open, double-row spherical roller bearing, self-aligning by virtue of the sphered outer raceway, sized 160×270×86 mm to the ISO 15 boundary plan. Numbering ties the bearing to its envelope: 23132 means spherical-roller type, dimension series 31, 160 mm bore — which is why the 270×86 mm outline swaps dimensionally with other ISO 15 bearings of the same code. In SKF suffix language, E marks the optimized high-capacity design and CC/W33 the pressed-steel-cage execution with relubrication groove; both are open bearings — the sealed variant carries the 2CS5 suffix and the vibrating-screen execution VA405. With C 1029 kN and C0 1370 kN, the 23132 load check covers radial plus moderate axial in either direction — but below the minimum load the rollers skid, so verify P ≥ 0.01·C0 at the lightest operating point. For relubrication, route the grease duct to the outer-ring W33 groove position where fitted, and purge until fresh grease appears at the seal — the 86 mm width across two roller rows needs the full charge.
Typical equipment & failure modes
Common applications
- heavy rolling-mill work-roll chocks
- large dredger and marine winch drums
- steel-plant continuous-caster segments
- large induced-draft fan rotors
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- cage pocket wear or fracture from roller skew at insufficient minimum load or rapid acceleration
- roller-end scoring from starved lubricant at start-up before the grease channel purges
- brinelling from static overload or impact during handling and mounting
Selection pitfalls — read before you substitute
- At 160 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23100-series series at 160 mm bore (270×86 mm) is the medium-OD wide envelope for heavy continuous duty; it is wider than a 222 bearing in the same OD class, so housing width and spacer stack must be re-checked before substitution.
- Open spherical roller bearings rely on the housing seals; in screening or crusher duty a failed seal lets grit into the sphered raceway and the 23132 pits long before its L10 life.
- Catalogue reference speed and limiting speed are different limits: the 1,900 r/min reference is a thermal criterion under load, while the 2,400 r/min limiting value is the mechanical ceiling — observe both.
- The 1029/1370 kN ratings are SKF catalogue values for this exact execution (23132 CC/W33); SKF can revise internal geometry without changing the order number, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the specification and re-verify for critical drives.
- SKF lists several executions of 23132 (cylindrical bore as listed, tapered-bore 23132 CCK/W33 variant, plus sealed and vibrating-screen options in the same envelope); they are not interchangeable order numbers — quote the full 23132 CC/W33 designation when purchasing.
Frequently asked questions
What are the dimensions and catalogue data of 23132?
The 23132 CC/W33 is a double-row spherical roller bearing with 160 mm bore, 270 mm outer diameter and 86 mm width (6.299 × 10.63 × 3.386 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 1029 kN, C0 1370 kN, fatigue load limit Pu 129 kN, reference speed 1,900 r/min, limiting speed 2,400 r/min, mass about 20500 g. It is an open, self-aligning bearing with two pressed-steel cages with a floating guide ring.
How does the 23132 bore code work?
The last two digits of 23132 are bore code 32, so 32 × 5 = 160 mm bore. The 270 mm OD and 86 mm width come from the ISO 15 dimension-series plan (dimension series 31 (medium OD, wide)), shared with other spherical roller bearings of the same code.
What does the CC/W33 suffix mean on 23132?
CC denotes two pressed-steel cages with a floating guide ring between the roller rows, and W33 adds an annular groove plus three lubrication holes in the outer ring for relubrication. CCK/W33 is the 1:12 tapered-bore counterpart.
Can 23132 accommodate misalignment and axial load?
Yes on both counts. The sphered outer raceway lets the bearing self-align ≈ 0.5–2.5° depending on series, absorbing shaft deflection and housing-seat errors. The two barrel-roller rows also carry bidirectional axial load in addition to heavy radial load — this is the key difference from cylindrical roller bearings, which take no axial load.
When should the tapered-bore 23132K variant be used instead?
Choose the K (1:12 tapered bore) variant when the bearing must seat on an adapter or withdrawal sleeve — typical for long shafts, frequent dismounting, or stepped shafts where machining a precision journal is impractical. Sleeve mounting requires measuring clearance reduction or axial drive-up, not nut torque. The cylindrical-bore 23132 listed here seats directly on a machined journal.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings on 2026-09-26. Read our editorial & correction policy.